Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
Hi again!
Thank you for all your answers this community is great! :-)
I am trying to develop a small app to be flashed on QFAB chips but I am facing a memory size problem...
While getting myself familiar with new SDK12 features I've noticed that when nrf_log uses deferred logging to RTT NRF_LOG_FINAL_FLUSH() results in unconditional breakpoint...
Hi guys,
Wanted to play around with the new SDK and the S332 Softdevice. I tried your multiprotocol example "ble_ant_app_hrm" with Keil.
Build fails:
http://dumptext...
Hi,
I am developing an app using the base module "ble_app_uart". In our application we would like to store data in the flash memory.
I am using "Flash Data Storage"...
I want to make my nRF52 turn on every 5 minutes, send data to a device over BLE and go back to sleep. For some reason once I turn on BLE advertising LED1 becomes solid and...
Dear Nordic Team,
Thanks for supporting.
We are worked in nRF51422 development kit.How can i enable DFU service in all BLE APP examples source codes in main.c
Please...
Hi,
when I use nRF Connect (or MCP before) to browse my BLE service, I get shown some garbage if I use many characteristics in my service.
When I use 45 characteristics...
Hello people,
I'd like to use the NRF52832 (QFAAB0) / PCA 10040 / S132 development board as a data logger. For that I soldered a micro-sd card reader and started using...
I set the connection as follows:
#define MIN_CONNECTION_INTERVAL (uint16_t) MSEC_TO_UNITS(500, UNIT_1_25_MS)
#define MAX_CONNECTION_INTERVAL (uint16_t) MSEC_TO_UNITS(1000...
I am trying to use the mesh network using the nrf51822. I have to use the app_timer with my application. Mesh library and the app_timer library making conflict with the SWI0...
I was trying out the low power PWM example and noticed the timing inaccuracy that was mentioned in documentation .
For example, with low_power_pwm_0,
period = 220...
I have checked the datasheet between 51422 and 51822,they look the same,but why the NRF51422 can flash BLE and ANT+,but 51822 can't? Is the Radio part different,or the Flash...
I have based my firmware on the Proximity Application example.
Now I need to extend my application to support BLE DFU service.
But as i read Extending your application...
Hi,
I am using the flash memory for a few variables and it works very well. Now I have one flag which is defined by #define statement and if it is enable then the initial...
