Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi all! I want to send data from a beacon (nrf51822) to a Pic microcontroller with the RS232 standard, what function should I use to send data? For example, I can use the...
Hi Nordic Developer Zone,
I also encounter a problem with enabling indications in my Android project. I want to enable Indications so I can gather informations store in...
Is anyone able to access the documentation for the Advertising Module?
Try this:
Go to the InfoCenter at:
infocenter.nordicsemi.com/index.jsp
Select the following...
Has anyone tried to plug an R3 shield to the nrf52 DK?
I was about to try, but it looks like the pins don't line up correctly - but then I have no experience with R3 shields...
Hello everyone,
I'm using the nRF52832, i would like to shutdown the timers, so i can enter the low power mode. In the datasheet tasks_shutdown for the timer modules is...
I have an application which receives commands from a co-processor via UART. Some commands are BLE-related such as, e.g. start-scan, stop-scan, connect, etc.
As the UART...
In nrf_drv_adc.c , there are loads of these ASSERT() macro calls:
ASSERT(mp_state == NRF_DRV_STATE_INITIALIZED);
But there is no variable mp_state. This will fail...
Hi! I have asked a question in this topic ( devzone.nordicsemi.com/.../) and now I can send one packet of 20bytes. What I cannot do is sending two packets at the same time...
I have nRF51 Dongle.
I can set it in BOOTLOADER mode and update firmware like:
developer.mbed.org/.../
I see the dongle in Device Manager/Disk drivers like "MBED microcontroller...
Hi all,
i have a little issue.
If i remove the bond information with app Master control panel, my slave cannot connect again with my phone. [Pairing Reject from Nordic_CTS...
I am moving from S110 and SDK 6 point something to S130 and SDK 10. I have my basic BLE code going but am unable to get the SPI back-in-action. I am using gcc and the s130...
I use NRF51822qfaa,s110 v8.0, now I use master TWI to drive the TWI bus chip.
the TWI bus chip Slave Address is 0x48.please see the below program .
question:
1.The...
this is the main program!
#include <stdbool.h>
#include <stdint.h>
#include "nrf_delay.h"
#include "nrf_gpio.h"
#include "boards.h"
const uint8_t leds_list[LEDS_NUMBER...
Hello,
I migrated from SDK 9 to 11 (S132) and i cannot receive anymore custom advertising (from another nRF52)
I receive another devices advertising events so reception...
I'm looking to use this dk for a small project.
Has anyone made or seen a box for the devkit easliy available (.STL) for 3d printing?
And for added coverage, can I just...
