Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
I made a custom board with nRF54L15. I do not have a spectrum analyzer, so I cannot tune how much power goes to the antenna or how much is radiated. So, I started ADV...
I have compiled two projects namely Blinky and ble_app_template.
Both projects run and debug but the radio portion in the ble-app_template is not functioning.
Having a compiled...
I have been reading a lot of post about static pairing passkey using S110. I have tried two example provided in this threads: devzone.nordicsemi.com/.../ devzone.nordicsemi...
Hi,
I have done the bonding and saving context to flash. As an example I used ble_app_template. I cutted all redundant code and limited to single bond for simplicity.
In...
I am trying to communicate between nrf51822 and Android device using Gatt. But nrf51822 invokes UartService.ACTION_GATT_DISCONNECTED after some time, the disconnection happens...
Hi,
until today we develop our application on Nordic DK with nRF1422 with 32 KB of RAM.
We are using S130 and SDK 8.1.0.
Today we saw that our target module, the MBH7BLZ07...
Hi!
I'm working with nRF51DK with s110 soft device on it. I'm trying to write simple custom service which reads some data from sensors and send it over BLE to Android app...
Hello,
I know the current limit of 15mA to share among all gpio pins.
If I source/sink current in very short bursts (100ns every 1ms) can I draw larger currents than 15...
Dear All,
We are working on a custom board with NRF51822.Everything works fine apart from the timer. What we are doing is that once the board is booted, it reads some values...
Situation:
We are building BLE device that have GATT service showing a analog sensor value.
AIN2 is connected to the sensor. AIN4 is connected to battery.
We would like...
Hi.
I use nrf51822 rev.3 build number CEAAE00(0x0079) package is WLCSP.
Before I got a experience already develop wearable device using rev.1 chip. And that board work...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
I was wondering if the Master Emulator API requires the Segger IC on the nRF51 Dongle (PCA10031) to work? Or is this just used for programming the nrf-device via USB?
The...
