Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
I use the chip nrf51822, However, SDK8.1.0 example ble_app_uart is base on nrf51422, what I need to do? just replace bsp.c ? and which bsp.c file corresponds to the nrf51822...
I'm tring to build a FOTA broadcaster machine using a raspberry-pi with bluez. or any other Linux small linux embedded system.
The idea is that after testing the board...
I cannot program an external nRF51822 module(program old softdevice S110 6.0.0) with nRF51-DK p20 (SWD), it give message "invalid parameter error".
and i program the 51422DK...
Hi all,
I want accive this situation. My peripheral connecting a central with a service for example hrs, then i stop the conect with the function sd_ble_gap_disconnect(m_conn_handle_peripheral...
Hi,
I am using the sample BLE_gls code provided by Nordic.
I have made the following changes in the code:
#define SEC_PARAM_MITM 0
#define SEC_PARAM_IO_CAPABILITIES...
I am using nrf51822 qfaa IC (pca10004 board) with softdevice v8 and sdk9. Now I am trying to do the dfu example. I uploaded the softdevice with the help of nrf gostudio. But...
Hi,
Please correct me if I'm wrong.
Consider an application that will read 6 bytes of data from I2C at 200Hz (each 5mSec) and will stop after 2000 reads. This will be...
Hi,
Apologies if this is an obvious question, but I haven't been able to establish from previous questions or the data sheet whether it is necessary to use an external...
I'd like to be able to change the connection interval from my central device on the fly after a BLE connection has been established between it and the peripheral. What's the...
Hi,
In the ble_app_proximity project in SDK 0.9.2, I was trying to add manufacturer data to the beacon. Here are some of the code snippets which I changed in main.c
#define...
Hello,
I am working on S120 stack with 9.0 SDK and testing with heartrate application and iPad as a peripheral. I am getting the central device as nRF51822 after central...
Do I need to implement my own timer to wrap this function? I appears that I might receive a BLE_GAP_EVT_TIMEOUT timeout event but testing has yet to reveal one.
My test...
Is there an example that is a minimal example of advertising on S110?
It might even serve one attribute that is set to a constant like '1234'.
This would help me bring...
HI
I am trying to use mkit as programmer by P20
FOR third part BLE brd
VDD---mkit.vdd
GND--mkit.gnd
SWD--P20.4
SWC--P20.5
bisides, for
P20.3(SH_VTG) connected...
We're going to be programming and debugging our prototype nRF51822 board using this adapter from Segger. It's the same connector as comes with the J-Link LITE in the dev kit...
