Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
Hello,
I'm looking for guidance and understanding of how to properly use the KMU and ITS for secure key storage of a key generated on device.
I see that typical ITS use...
Hello,
I'm currently using Visual Studio Code with the newest SDK, Toolchain and Plugin on MacOS and most of my applications are freestanding applications.
Now I want...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
I have been reading a lot of post about static pairing passkey using S110. I have tried two example provided in this threads: devzone.nordicsemi.com/.../ devzone.nordicsemi...
Hi,
I have done the bonding and saving context to flash. As an example I used ble_app_template. I cutted all redundant code and limited to single bond for simplicity.
In...
I am trying to communicate between nrf51822 and Android device using Gatt. But nrf51822 invokes UartService.ACTION_GATT_DISCONNECTED after some time, the disconnection happens...
Hi,
until today we develop our application on Nordic DK with nRF1422 with 32 KB of RAM.
We are using S130 and SDK 8.1.0.
Today we saw that our target module, the MBH7BLZ07...
Hi!
I'm working with nRF51DK with s110 soft device on it. I'm trying to write simple custom service which reads some data from sensors and send it over BLE to Android app...
Hello,
I know the current limit of 15mA to share among all gpio pins.
If I source/sink current in very short bursts (100ns every 1ms) can I draw larger currents than 15...
Dear All,
We are working on a custom board with NRF51822.Everything works fine apart from the timer. What we are doing is that once the board is booted, it reads some values...
Situation:
We are building BLE device that have GATT service showing a analog sensor value.
AIN2 is connected to the sensor. AIN4 is connected to battery.
We would like...
Hi.
I use nrf51822 rev.3 build number CEAAE00(0x0079) package is WLCSP.
Before I got a experience already develop wearable device using rev.1 chip. And that board work...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
I was wondering if the Master Emulator API requires the Segger IC on the nRF51 Dongle (PCA10031) to work? Or is this just used for programming the nrf-device via USB?
The...
Hi.
I'm using latest version of nrf51-pwm-library to test if PWM works fine, but unfortunately, it's not. I have very simple program which should fade LED from 255 to 0...
