Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
nrf5340DK
NCS 3.0.0
if I use sample zephyr/samples/boards/nordic/system_off it works fine and i can wake from sw0 press. but if i move the sys_poweroff() call int a...
Hi Team,
Recently we did a network related testing for our CL5G modem (nrf9160) and observed a problem, in this test we used a nmap tool, this tool will search for open...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
It's my question. I use saadc single mode from nrf52832 to sample voltage .When the original voltage is 24 V ,measurement of the pin is 2.8v,I set the resolution to 10 BITS...
hi,dear engineers,
i use the example experimental_ble_app_buttonless_dfu of nRF5_SDK_13.0.0_04a0bfd,
on the PCA10040 board,Now,i'm sure that I am flashed Softdevice,app...
hi
I have designed a small PCB with the NRF52 chip on it and kept few ports for some peripherals. Apart from that I only have 4 pins that I can connect to, UART-Tx, UART...
Hello,
I'm wondering if my nRF DK51 is not broken as it behaves quite strange when trying to connect with a BLE Central (iOS and Android devices). For most of the part...
I am trying to track down a power usage problem with my code. When I started using SDK 13.0.0/S140 v5.0.0-2.alpha on a PCA10056, the power usage went up in my app. I see that...
I'll try to simplify my project as much as possible to make this understandable.
I'm wiring an nRF52 PCA10040 board to an iCE5LP (Lattice) FPGA.
I'm having an issue with...
I have an after market breakout board for nrf51822 with a usb-to-serial chip (cp2102) that I bought from Amazon . It should act as an NRF51 USB dongle (pca10031-like) but...
My pc server should send information to nrf52832 by ECDH, then I create a dll file from micro-ecc. However,the result in windows is not the same as the result in nrf52832...
dear friends ,
within a peripheral connection event, 9 states is identified, as it is shown in the pic above(from s132 document). Can i get a detailed description about what...
Hi @ all,
I am working with IoT SDK 0.9 and nRF52DK.
I have trouble with the lwIP CoAP client example.
Everything works so far, the board is connected and I'm able...
Hello! I am using a custom board that contains a nRF52832 device. The board has the SWDIO and SWDCK lines connected, which I have successfully been using to flash and debug...
I'm migrating to the new 13.0.0 SDK and I'm wondering what are the benefits of using nrf_serial over app_uart (if any) and what steps I would need to take to switch over if...
I have successfully manged to achieve serial communication between my PC (Windows) and nRF52 board by using the pc-ble-library and the pc-ble-library-js .
I can run without...
