Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,
I wrote my own nRF24L01+ library for my AVR AtMega2560. I used the datasheet and the widely used Mirf library as my guide. I am happy to say I got it working. I have...
I have a new PC (running 64 bit Windows 7) and am having issues after install nrfgo studio. I had it running previously on another windows 7 (64 bit) machine with no issues...
I noticed that there can be three SPI instances (SPI0, SPI1, SPI2) for the nRF52. Is it possible to have three TWI instances? We have a sensor network that requires 6 of the...
i have used 52832 for pdm clock generater, but i just can set the frequecy to fixed such as 1.032 MHz,1.067 MHz.., if i want to set the frequecy to 1.050MHz, i can't come...
Hi,
I am trying to run LWM2M support based on Contiki OS (contiki/examples/ipso-objects) on a NRF52 (PCA10040) development board. I can successfully build (make TARGET...
I see Nordic release pc-ble-driver 2.0.0 some time ago. I'm using 1.0.0, before I upgrade to the new version, I'd like to know what's new in it....could not find any list...
Hello,
I am using nrf51822 SDK11 S130.
I am using my custom design board which is powered by 12V. The nrf51822 is provided with 3.3V. I used 27k and 9.53K resistors in...
Hi,
I have two nrf52832 boards. One as mater and other as slave. I'm trying to develop a communication between master and slave through ble. Also i need to connect the master...
Hello, can someone tell me how I can change this, as shown in the picture?
Strangely, I have already selected the proper target device, as shown in this pic:
What...
I want to use UART to read GPS data while advertising.
After I add uart function to ble_beacon_example, UART API app_uart_get() always return NRF_ERROR_NOT_FOUND.What can...
Hi,
Can Anyone has experienced with nRF52 PWM clock generation ? I am trying to generate 8-Mhz clock out of GPIO by configuring it for PWM module.. But so far I can get...
I have taken ble_app_ancs_c_s130_pca10028 example of sdk11,s130 version 2.0.0 and i integrated Alert Notification Service,DIS[device information service] and DFU... Device...
I'm using the latest version of Keil with Software Packs. As I understood, copies of configurable files are stored in RTE folder. Non-configurable files are stored inside...
When i connect the board to pc its not detected and No J-link device in device manager
But when i press and hold the IF BOOT/RESET button and power cycle the board the LED5...
