I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to try out some changes that are not yet in the stable NCS releases, so I'm trying to build my Matter application using NCS v3.1.0-preview4. Unfortunately it gives...
Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am working on an nRF52832 application that uses SoftDevice S132 v3.0.0 as BLE central, BLE observer, and a proprietary protocol using the timeslot API.
Sometimes...
I have a Redbear BLENDv2 and want to program it with Keil. I am new to both Nordik SDK and Keil. Any help how to get to the example or open the example projects
Hello,
My question is about the case when initiator device attempting to restart encryprion with previously bonded responding device that lost the bond context.
As usual...
Hello,
I am trying to interface bme 280 with nrf52. I am using sdk12.2.2 and referring code twi_sensor.
I am able to initialize the I2C drivers and I can read the chip...
Hi,
My name is Bruno, and I am working with a Bluetooth module from u-blox(NINA B112-00B) which contains a nordicSemi board nRF52832 with a Cortex M4 processor. I'm getting...
Hello,
I am trying to combine Softdevice, bootloader, and Application hex files in single hex file.
Currently using s130, SDK11, nrf51822.
I combined files using this...
1, run NRF52832\nRF5_SDK_13.0.0_04a0bfd\examples\peripheral\uart, uarte_irq_handler can get irq when receive a byte.
2, run NRF52832\nRF5_SDK_13.0.0_04a0bfd\examples\proprietary_rf...
Hi,
I made an experiment and the result doesn't correspond with my view on how the BLE communication "connection" mechanism works.
I have an app running on the nRF52832...
Hello All
I am using following SDK version 12.2.0.i am facing some problem in some example project
could you please help me
If i flash the pre compiled hex file...
I held the boot button to enter bootloader mode, and accidentally dropped a hex file into the drive that popped up. Now I can no longer get a comm port to show up on the PC...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
(nRF51822, but also concerned with nRF52832, SD130, SDK 12.1)
I'm trying to write/erase flash from a bluetooth event handler. As it's been outlined in other questions,...
Hi,
I am just updating my application from SDK13.0.0 to SDK14.0.0.
2 Services are in use: DIS and NUS. To advertise that, I made use of the scan response functionality...
