We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Keep hitting my head on this inconvenient workflow.
Edit build config
Select target custom board
Build config
All OK
Edit config again
Target board has been...
I have used the Programmer previously with success. I am attempting to program the Dongle (10059) with a slightly modified version of ble_nusc_usb_dongle. Although it claims...
Hello Team,
I have flashed the bap_unicast_server bluetooth sample on my nRF5340 Audio DK. No build or flash errors. When I connect to my phone it connects properly. I'm...
I'm working on a project involving a USB dongle based on the nRF52840 SDK-2.9.1, which needs to communicate with a sensor (also an nRF52840) and transmit data via USB to PC...
Hi, what I did is wrote below:
1/ I program the S120 softdevice to the nRF51822 board, using nRFgo studio software(the softdevice size is set to 80KB).
2/ I complied the...
Hello,
I recently tested the nRF51822 with a non-Nordic BLE devices and encountered some problems. When testing with Nordic the connection is maintained with no problem...
During testing I changed the device name in the DFU. After making the change the DFU client in the master control panel would no longer work.
Is it possible to make the...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
Hi
I try to configure a ppi channel with timers to generate pwm signal
My entire code is working well without softdevice.
Here my ppi init function:
NRF_PPI->CH[0...
I am planning to build mobile devices that communicate directly between them with BLE. The devices are all the same and carried by users. users meet and exchange data. I can...
hi,all!
i am confused about whicn priority should i set for my interrupt.
For deteils, I need a gpioe interrupt for my button, and this button is used to POWER OFF my...
We wish to make a universal device that may used
for ANT with the nrf51422 and the 32kHz crystal.
or for BLE with the nrf51822 without the 32kHz crystal.
Will there be...
I'm trying to bring up a basic S120 application on PCA10001 based on the multilink central example, using the IAR toolchain.
I've programmed the S120 device using 1.0.0_3...
I'm developing a next generation device using nrf51822. To replicate existing behavior I'm trying to sniff the previous generation product behavior using the ble sniffer on...
Hello!
I am working with a NRF51822 and I need to change the address of pipes regularly (so I can use more than 8 NRF communicating together with ESB protocol).
My problem...
Hi,
I'm trying to understand if S120 soft device provides user configurable option for duplicate filtering of advertisement data. I couldn't find any info on the SoftDevice...
Hi,
I used the project gzll_ack_payload in nRF51 SDK for nRF51822, I changed the Device to send a packet per second, every thing goes OK with the default parameter.
...
Hi,
there is an example named gzll_ack_payload in the SDK of nrf51822.
when nrf51822 works in device mode, if a packet is send successfully, the funciton of nrf_gzll_device_tx_success...
