I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
nrf24LE1 external interrupt is not easy to use , I use nRF24LE1 48pin chip, and the external interrupt 0 (GPINT0)is configured to falling edge trigger, but it can not be triggered...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Everything was fine until I updated to the latest SDK version 6.0.0 and the new nRFGo ap version 1.16.1. Now when I try and connect to my device I get J-LinkV4.52c Error ...
Hi all,
I am trying to send and receive generic data from the L2CAP layer. So, initially I am just trying to send data with sd_ble_l2cap_tx with S110. The code that I am...
We are considering moving from the nrf51822 wlcsp to the qfn48.
We would like to minimize the changes to our design. Can we, should we keep our wlcsp antenna design and...
Exactly what baluns are known to work with the nRF51822. I believe there is the STMicro balun and am uncertain about the status of the Johansen balun. Is there a list of preferred...
Hi,
We are using nRF51422 in our project and we observe a strange thing, that even there is no external pull up resistors, the I2C communication using the built-in TWI...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Hi,
I am trying to create a star network with 12-16 slaves and one master.
The master would be a nrf51822 and the slaves nRF8001/2.
The slaves would not transmit...
Hi,
I'm using the UART_OVER_BTLE base example and I'm investigating what needs to be done to enable security.
Using the Following security configuration the device stops...
Can you tell me which antennaes i can connect with nRF 8001 to make it discoverable and transfer data. And i think pi network is solved depending on the antennae only. Can...
Hi,
Is it possible to extend the RAM memory by using internal flash memory?
Actually i need to collect 4KB of data from accelerometer and flash it to the EEPROM when there...
