Hello,
I know this question is more related to Zephyr than Nordic, but I wanted to try asking here.
I’m using the SMP service to send files to my device on a LittleFS...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
Hello Nordic team,
I've recently upgraded my application from nRF Connect SDK v2.7.0 to v2.8.0 , and the previous BLE Disconnect issue has been resolved — thanks again for...
Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Hello,
I am using nRF5_SDK_12.0.0 with soft device s130_nrf51_2.0.1_softdevice. I am trying to implement the DFU service in my application, for which I am following:
...
Hello :) I'm trying to run the DFU example (dfu_dual_bank_ble_s132_pca10040) for the nrf52832 chip on a custom board. The Bootloader crashes/resets at the SOFTDEVICE_HANDLER_INIT...
spi.rar
Hi,
As a beginner, I want to combine spi and uart example in nrf52 11.0.0 sdk, for my application. I have included all libraries and driver files from uart in...
Hi,
I would like to ask your support for a very unusual problem that I'm facing with a project based on nrf51822.
The board under test is based on nrf51822, SDK12.1...
Hi all,
I'm trying to set up DFU over BLE - Single Bank using:
Mac OS 10.10.1
gcc 4.9 SDK 7.1 w SD110 7.1.0
PCA10001 v2.2.0
MCP 3.7.1.8567 (modified lib/dfu folder...
I've read a lot of questions regarding the AES decryption using the nrf51 where it was not possible. Is it now possible with the nrf52 or the even newer version?
Thanks,...
this is capture image.
what does that happen?
The debugger is I-Jet and debugging via SWD.
The connection did below. and I'll assume the red line is number one. I...
Hi
I was playing around with the new serialization code in the SDK 13.0.0 and the PCA10056. I was able to compile the connectivity code, but when I try to configure the...
hi, all
I want to run nrf's example named "proprietary_rf->esb_prx", the deafult setting of keil memory is
IROM1: 0X0 0X80000
IRAM1: 0X20000000 0X10000
It can compile...
Hi,
We want to make PCB of NRF52 and we want to buy PCB design software.
Can you guide me that how many layers of PCB is required and how many pins will be required...
I've searched for enabling notification, but there are some points that I can't understand.
GATT characteristic attributes and characteristic cccd values are dedicated...
Hello,
When I check RESETREAS, I have some reboot reasons rised from software error (SREQ).
I know that these errors are not catched in the app_error_handler because...
I am using ARM-GCC (version 6.2 2016q4) toolchain and make command to compile example code.
I have updated my compiler installation path in Makefile.Windows as well.
...
