Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
Hi all:
I download nRF51-ble-bcast-mesh from GitHub ,and put this project under below folder
...SDK8.1.0\examples\nRF51-ble-bcast-mesh-master\
compile this example...
I was doing power profiling using the PPK. All was working OK, as far as I went. I disconnected the PPK, and returned to normal debugging with stand-alone DK. Now I can't...
hi,all
S110 NRF51822 SDK8.0.0 server
i want to increase the througout speed,the SDK8.0.0 support changing MTU size?
MTU Can be in 4.0 protocol is modified?
if SDK8.0...
Hello,
I am starting to create a bootloader and I want it to be independant of the SoftDevice. Is there any open source implementation of a flash_write function that I...
Hi
officially for the nrf51 chip, 40 ppm frequency tolerance recommended but I'm not able to find this much of tolerance in digikey.
The only matching crystal digikey...
I am trying to get a NRF HRS central (ble_app_hrs_c) to make a connection to a NRF HRS peripheral (ble_app_hrs). However, the peripheral does not show up whenever the central...
It seems like a really great company, but after exploring and asking , and searching for a good BLE solution, I just can't find a good fit.
So you want a GOOD processor...
What is the Best way to send float over BLE?
Values range between -2.000volt and +2.000Volt (-2000mV / +2000mV)
Do I break it into two uint8_t and manipulate the +/- sign...
I am engineer, and I may be sensitive to user experience, or just a bad engineer but I do not get this.
I read ALL the guides available in the last 5 hours,
this
this...
Hello,
I have just migrated my project from sdk 9 to sdk 12.2....and of course from Device Manager to Peer manager. My initial project which was built off of the sdk 9...
During the webcast earlier this week, we were shown a phone pairing with the nRF52 dev board using NFC.
Is the code used for that NFC demo available as an example project...
Hi,
I am using nRF52832 as the core of my device that works with battery. I have to keep the SoC powered on all the time. When the off push-button is pressed I restart...
I am using a nrf52832 to communicate via UART to a GSM module (AT commands).
I have setup the device with a baud rate of 9600 and using HW flowcontrol. The nrf52 is doing...
i want to communicate nrf52dk with arduino over spi.i want use nrf52dk as a master and ardunio as a slave.kindly refer me some example or code or any thing which s helpful...