We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
That is probably an old topic, but after doing some research I could figure it out: calling sd_app_evt_wait() on my nRF5832 + nRF5 v11.0.0 SDK + s132 causes my chip to reset...
Hi
I've some troubles with the ble disconnection of S110.
Always when I call the sd_ble_gap_disconnect function after successful connected, the error code 8 NRF_ERROR_INVALID_STATE...
As I can see, I flashed Zephyr to Carbon 96 board, I don't fully understand the process,
I mean, I see .bin and .elf files but i don't see boot.img file, how do i make a...
The nRF52832 datasheet refers to a transmission of multiple packets in Figure 37. I have attempted to load multiple packets to the radio FIFO using nrf_esb_write_payload(...
Hi All,
I have developed an application on the RedBear BLE Nano2, and am trying to port it accross to a custom nRF52 board.
The Hex that the Arduino IDE outputs does...
I have an application which requires protection from passive eavesdropping, but not man in the middle attacks. I want to enforce the use of diffie hellman key exchange.
...
Hello
i am using Nrf52840 with sdk 132 and version 12.2
i am using the Heart Rate example as template.now i am just testing.
Before making connection,i like to Advertise...
I have a sensor which has output in the range of 0-5V. I want to connect it to an nrf51822 GPIO pin and to be able to read the value via it's 10 bit ADC. Is there any guide...
hello, there my application is like that...
(1) calculate size of receive buffer. than read that size of data.
again new data comes, then again calculate that size of...
Issue: With my external antenna design, I get lower dbm than PCB antenna (nRF51DK) with same distance.
My external antenna design: -70dbm
nRF51DK: -40dbm
In this...
Today when I started power profiler kit, it suddenly started to show peak values like 80 mA. This has not happened before, but the values with the same hardware have been...
In the data sheet of the NRF51 and 52 there is mention that sensitivity of NRF51 is -96 dBm and NRF52 -98.
But I read some where that when RSSI is -90 then that signal...
We are working on a dynamic radio power change for a proprietary RF protocol, and we are missing some granularity on the NRF_RADIO->POWER levels.
Typically we would need...
I am wondering what is the logic and magic behind using sdk API's to advertise vendor specific 128-bit service UUIDs. In the "Nordic UART Service" example (nus, SDK12.2.0...
