Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I am about to develop a Bluetooth Mesh network with the nRF52832.
With the PCA10040, i already able to form a Bluetooth Mesh Network, such that there is one client act...
Does anyone know where I can find a list of which phones/tablets support Data Length Extension (DLE)?
We are finding that many budget phones (e.g. Motorola G6, Samsung Galaxy...
Hi,
I'm using nRF52840 (rev 1.0.0) and Mesh 2.0.1 and SD 15.0.0.
I added FreeRTOS following the example "hrs FreeRTOS".
In FreeRTOS, the source clock (configTICK_SOURCE...
Hi,
I'm trying to use RTC2 as a custom timer using the RTC Driver, initialised as :
nrf_drv_rtc_t erx_timer_rtc = NRF_DRV_RTC_INSTANCE(2);
But when the BSP library or...
Good morning everyone,
I read a lot of threads in the last week on this subject, but so far I was not able to find a solution to the problem.
On a custom board we are...
Is it possible to use both Zigbee & BLE SDKs at same time? Actually we are planning to use NRF52840 for our next project. In which BLE will be used for Smartphone to NRF communication...
Hi there,
I have suitably designed a battery sampling circuit in my prototype configuration, (Vdd = 1.8V, battery swing = 4.2V to 2.9V) using the app note provided at: https...
I am getting the following error when trying to compile port.c
../../../../../Nordic_Semi/nRF5_SDK_14_2/external/freertos/portable/ARM/nrf52/port.c:93:7: error: expected...
Hello,
Is there any sample code which performs only the most basic functions?
Ie. - Sample code in its simplest form which only sets one pin to an output and sets it...
I'm using SDK 15 and soft device S132 6.0. Using nrf Toolbox to update custom firmware, I'm running into a situation where the DFU update fails with an error code 4 when trying...
Hello,
I have been doing research trying to figure out how to program just the nRF52832 chip. I want to program the nRF52832 chip with the Arduino IDE from sandeepmistry...
Hello!
I am using the nRF2740 board with the nRF8001. If I connect all the pins (SPI, RESET, RDYN, GND) except the Vcc pin I still measure 2.5V at the Vcc pin (Connector...
Hello everyone,
In my current application , I am using nRF52832, with the SDK 11.0. I have a problem with the BLE connectivity, which I think is a hardware issue.
With...
I am doing a connectionless system where I am just broadcasting the data. I am showing a loss of about 50% on the receiver missing the data packets. I have tried before to...
Hello,
I configured pin P1.15 as output and with GPIO_PIN_CNF_DRIVE_H0H1 but I only get 1.7V ?
Does "standard drive" means that the pins can't get to 3V ?
Thank...
