Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
We have an nRF51822 peripheral device that is bonded with one and only one central. The central is always an iOS or Android phone running our app, which is scanning at "low...
In the BLE advertising library, in SDK 11, is the timeout for directed slow advertising specified in seconds, or in number of tries?
Seconds would be more consistent with...
Hi All,
I have got a project running on an nRF51422 QFAC, using the lastest SDK.
I am having some problems with the app_timers, i am able to create and start them, and...
Hello all,
i am working with the nRF52832 DK and SDK11. Actually the Enhanced Shock Burst Communication is working. I can send and receive messages. From this point on...
Lets say, that I've got a chip with program in its flash. I know I can protect it from being read back, but can I protect it from flashing anything else through debugger interface...
we have two nrf51-dks and we wanna create a ble mesh.
how can we set a ble mesh and same time ble advertising on Nrf51422 DK (PCA10028 V1.2.0) Board with using examples on...
Hello,
is there a possibility on nrf51 8.0.0 softdevice to determine whether particular notification has been received by remote device?
I use sd_ble_gatts_hvx() to send...
I am facing some problems with the app_timer api. In my application I have created two app timers. The timer api is using the swi1 interrupt for its working. I am using it...
During DFU with the nrf Connect app I get the error REMOTE DFU OPERATION FAILED. Here is the log file:
http://pastebin.com/y7hFNSBq
Using NRF5 SDK12 / NRF51 DK
...
Hi, Nordic
I have two nRF52 and one nRF24LU1.I want to use Gzp. two nRF52 pairs to the nRF24.
I use nRF5 SDK13 GZP device sample, nRF24 Gzp host sample.
But only...
Hi
We are very interested to test the wireless range using Bluetooth 5, 125 kbps long range mode.
If we purhase two nRF52840 Preview DK boards, is there a easy way to...
Hello,
Currently i am doing some testing with the NRF52 DK.
I am measuring the time it takes to send and receive a BLE message.
I am using the high bandwidth setting...
Hi all,
Someone can give me a information about the difference between function uint32_t err_code = sd_ble_gap_adv_stop(); and stop the advertising with using the timeout...
hi everyone i'm using 9 axis imu sensor with the nrf51822 board and i'm confusing in how to calculate the roll,pitch and yaw values,can you please suggest me some methods...
I recently purchased the NRF52832-QFAA Nordic SoC, and am having trouble finding information in the documentation about FCC ID and CE mark testing. Thank you.
