Nordic #Devacademy intermediate course: Ticket for exercise 2 of lesson 2
Dear Colleagues,
I selected the #nRF9151-DK, since it was in the list of recommended boards for...
Hello,
I am developping an application based on PAwR (Periodic Advertsing with response) in coded PHY (S8) extended advertising on SDK 2.7.0.
costum chip nrf52840 (on...
Hi everyone, I have a custom board in nrf52833. Currently, the gpios on nrf52833 are gone, except for the NReset pin (P0.18). Can I configure the NReset GPIO as a GPIO I/O...
My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
I am currently attempting to send HTTP requests (GET and POST) with my nRF9160 DK over an LTE connection. I have tried running the HTTP client sample code under zephyr/samples...
Hi,
Currently, we develop a prototype that needs to communicate with WuR; the FH101RF. Could you please tell me if it is possible to communicate with it? If not, can you...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
When I keep this function :
static void vMain_iInitDeviceManager_Exe(bool erase_bonds)
{
uint32_t err_code;
dm_init_param_t init_param = {.clear_persistent_data =...
Hi, everyone.
I've developed a custom board using nrf52832. I tested it and found that CPU core, GPIO and other peripherals work well, but BLE doesn't work at all.
I ran...
Hi,
Raspberry (SPI Master) -> NRF52832 (SPI Slave)
The code below execute event_handler of SPI with NRF_DRV_SPIS_XFER_DONE type. But RX buffer is empty. All bytes are...
Greetings,
I'm in the process of choosing a nRF52 module. I know of this link for the various modules www.nordicsemi.com/.../3rd-Party-Bluetooth-low-energy-Modules.
I...
Hello, I've been trying to get directed advertising and auto-connection working on an NRF51822 peripheral.
I'm using SDK V11.0 with SD130 v2.0.1
This is the scenario...
Hi,
I used the code ble_app_uart_c on board 10028 as a base for my custom board.
My board is nrf51822 QFAA based so I changed all occurances of nrf51422 to nrf51822...
Hello,
We are trying to communicate to this board ( www.adafruit.com/.../1697 ) that has nRF8001 at its core.
Unfortunately, our TX is only able to output BLE 4.2
...
I'm running on nRF51822, SDK 8 (not totally sure, I inherited the project), SD130 and mbed.
I've tried and failed with my own code to use pstorage.
I'm now trying a...
Hi. I'm using nRF51822AC, SDK12.2.0, S130.
The size of "s130_nrf51_2.0.1_softdevice.hex" in SDK is almost 300KB.
But chip's flash mem size is just 256KB. It's bigger than...
How is it used? And why to use it?
static nrf_saadc_value_t m_buffer_pool[2][SAMPLES_IN_BUFFER];
instead of
static nrf_saadc_value_t m_buffer[SAMPLES_IN_BUFFER];
Hi team,
we are doing project called indoor navigation using beacons.To get the good RSSI signal strength,in which position should i need to place the beacon. Can any one...
Hello,
I tried to flash an application to the nRF52832. First I flashed the softdevice, after that I flashed the bootloader and next the application.
The application...
