I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Dear all,
i configure pin 3 to float input.when the pin3 input 0.3VDD--0.7VDD,the chip current have 25--400ua,other is normal(4ua) Why?
SDK:8.1.0
s110
#define PHOTO_PIN_NUMBER...
Hi,
I am using nrf pwm library from here: github.com/.../nrf51-pwm-library . I am driving two gpios for a piezo buzzer.
I call pwm_init(), then use the call set_frequency_and_duty_cycle...
Hi,
I am trying to run a MIDI slave chip with the nRF51822 which requires me to use the MIDI standard baud rate of 31250. Is it possible to use nrf_drv_uart with a custom...
Hi all,
i use the function sd_power_system_off() to put the micro in system off.
First question is about the the type of system off. There are different type of system OFF...
Hi Forum and Nordic Employess
I use sdk12.2
The Pstorage libraries are missing. I want a Pstorage (flash write / read) example along with the Soft Device.
Thank You
Hi all,
I see there are similar questions posted on this forum, but none answers my question satisfactorily.
What I have:
we use the nRF52 we use UART0 to
transmit...
I'm using SAADC on a NRF52832 DK to read a analog channel between 0-3.3V. I wanted to supply current with the board VDD but it's value is 2.8V and they're not event stable...
Hi
I'm trying to get higher throughput when connected as a central by increasing my Tx&Rx bandwidth to high (from the default medium).
uint32_t nrfErr; ble_opt_t opt...
Hello,
my custom board does not have external 32kHz crystal. I have managed to use NRF_CLOCK_LF_SRC_RC in SOFTDEVICE_HANDLER_INIT instead.
My questions are:
...
I have a Custom Board made by using nrf51822 soc but pc is unable to detect the board by using Jlink debugger.
Stlink was able to detect only when frequency selected as 20khz...
Hello dear Nordic Team,
I got a question regarding the device filtering options. I am interested in putting 10 chips next to each other. But every chip shall have only...
As I came to understand, all the services & characteristics are registered in a "GATT table" of some sort, so my question:
What are the functions used to create and...
I want to update the nordic device from another MCU with HCI DFU. I cannot figure out how to write the packet header.
In the Nordic documentation, it is writen to read the...
I want to add micro-ecc library for compiling bootloader secure code.
I tried as mentioned on infocenter.nordicsemi.com/index.jsp .
I am getting error as attached. I am...