hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hello,
if we want protect our (central) device against tracking and still allow it to connect with specific Peripheral we can use whitelist with IRK (and?) mac address...
eclipse_log.txt
link text
hello there i am trying to make environment for gcc and eclipse with nrf51. i am following above link. i changed my Makefile.winows ...
Dear all，
i configure pin 3 to float input.when the pin3 input 0.3VDD--0.7VDD,the chip current have 25--400ua,other is normal(4ua) Why?
SDK:8.1.0
s110
#define PHOTO_PIN_NUMBER...
Hi,
I am using nrf pwm library from here: github.com/.../nrf51-pwm-library . I am driving two gpios for a piezo buzzer.
I call pwm_init(), then use the call set_frequency_and_duty_cycle...
Hi,
I am trying to run a MIDI slave chip with the nRF51822 which requires me to use the MIDI standard baud rate of 31250. Is it possible to use nrf_drv_uart with a custom...
Hi all,
i use the function sd_power_system_off() to put the micro in system off.
First question is about the the type of system off. There are different type of system OFF...
Hi Forum and Nordic Employess
I use sdk12.2
The Pstorage libraries are missing. I want a Pstorage (flash write / read) example along with the Soft Device.
Thank You
Hi all,
I see there are similar questions posted on this forum, but none answers my question satisfactorily.
What I have:
we use the nRF52 we use UART0 to
transmit...
I'm using SAADC on a NRF52832 DK to read a analog channel between 0-3.3V. I wanted to supply current with the board VDD but it's value is 2.8V and they're not event stable...
Hi
I'm trying to get higher throughput when connected as a central by increasing my Tx&Rx bandwidth to high (from the default medium).
uint32_t nrfErr; ble_opt_t opt...
Hello,
my custom board does not have external 32kHz crystal. I have managed to use NRF_CLOCK_LF_SRC_RC in SOFTDEVICE_HANDLER_INIT instead.
My questions are:
...
I have a Custom Board made by using nrf51822 soc but pc is unable to detect the board by using Jlink debugger.
Stlink was able to detect only when frequency selected as 20khz...
Hello dear Nordic Team,
I got a question regarding the device filtering options. I am interested in putting 10 chips next to each other. But every chip shall have only...
As I came to understand, all the services & characteristics are registered in a "GATT table" of some sort, so my question:
What are the functions used to create and...
I want to update the nordic device from another MCU with HCI DFU. I cannot figure out how to write the packet header.
In the Nordic documentation, it is writen to read the...
