I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hello
I tested a BMD-300 Module and Nordic Team has been very helpful.
I tried to reach the maximum speed in this module.
I like to send 4x20 byte per 30 ms, but I...
Hi all,
I am using as base the Experimental ble_app_blinky_central and ble_app_blinky examples.
I noticed using a sniffer that the Central is asking to the peripheral...
Hello,
I am going to us the meander antenna from the nrf51 usb dongle. Are there any drafts with correct dimensions? And second what should be the minimum distance between...
I've been through the tutorial of connecting the NRD52 board to my PC, but my PC isnt recognizing it at all. No pop up for any usb devices. I've tried different cables and...
Dear Nordic Team,
Thanks for supporting.
currently i am try to interface MMA8453 accelerator with ble proximitty example .Already i have interfaced peripheral example...
Hello, I am new to NRF. and actually i dont have other MCU experience, beside adrduino.
my question is not about BLE/BLE+,
it's more about how to use NRF5283 in keil question...
SDK 13 Alpha
The header guard in serialization/connectivity/codecs/s132_s140/serializers/ble_l2cap_conn.h looks like this:
#ifndef BLE_L2CAP_CONN_H__
#define BLE_L2CAP_CON__H__...
Hello,
I really like the new nRF52840, especially it's Bluetooth 5 capabilities. The thing is that i cannot figure out if i would be able to make nRF52840 based devices...
Hello,
I have tried to debug ble_app_uart_pca10040_s132 application included in nordic SDK12.2 with Segger Embedded studio v3.12, but even though I don't get error while...
I have been working on an application for iOS for a few months now, and I want to give my users the best experience possible, when it comes to the peripheral I intend to use...
I would like to test the Fatfs demo using a target spi flash memory chip. The example code calls out sd card fatfs driver. Can I assume that spi flash memory is the same as...
I'm building a software for the nrf5822 using pc10028. I'm using CMake and after following both morf.lv/modules.php and devzone.nordicsemi.com/.../ I successfully made the...
Hello Noridc,
Liking your solutions, and I appreciate the thorough documentation.
Working on layout and so I was looking carefully at your reference design Gerbers for...
