Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
I am working with nrf51, SDK 11, S130, Keil uVision 5 and have an Application with RTX and want to use DFU OTA.
The bootloader works with the app_hrs_dfu example.
When...
Hi, I tried to enable non-connectable advertising timeout using the macro APP_CFG_NON_CONN_ADV_TIMEOUT in es_app_config.h, but it has no effect. I test this using nRF connect...
Hello,
When I call TASK_START in SPI Master it does not start a transfer. According to registers all seems to be set.
I found what was the problem. When I called TASKS_SUSPEND...
I am using SDk 11. S130 V2.0
What is the equivalent of spi_master_evt_handler_reg ?
I just want to configure my handler to receive the interrupt of the SPI master.
Please...
Hello, I've just purchased nRF52 dev kit and I'm using ble_app_uart example from SDK_12.2 to send/receive data from one pc (which is connected to the dev kit through usb)...
I have been trying to use nRF5 SDK 12 on nRF52 Preview DK by using PCA10040 instead of the removed PCA10036. But example 'ble_app_hrs' that uses SoftDevice S132 v3.0 do not...
Hello,
I am developing a custom board using nRF52. In my previous custom board, the total current consumption is 15mA with DCDC regulator enabled. I want to reduce this...
Hi,
I'm trespassing some code of nRF51 to nRF52 (s132, SDK 12.2.0) and I get an error when I try to call sd_ble_gatts_rw_authorize_reply. This is the code
case BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST...
I'm using the beacon example (SDK 12.2.0) which I've modified slightly so that a sensor output initiates advertising for 20 seconds with LED1 flashing accordingly. I want...
Hello I was working with the Flash Storage examples in the nordic github repo. I noticed that the FDS example while it has a IAR Workspace it does not have the associated...
Hi,
I am having trouble with buttonless DFU on my application. I am working on custom hardware on the nRF51822, SDK10.0.0, S130.
When I enter DFU from my application...
I'm working with pca10028.
Then gpiote interrupt is triggered twice.
Why is this happening?
And what is BUTTONx_EXT connected to PCAL6408A(U7) in schematics?
Hi,
I am new to nordic development. I have programmed segger program softdevice by s110_nrf51_8.0.0_softdevice.hex and program bootloader by dfu_dual_bank_ble_s110_pca10028...
My project is to communicate with the AD7780 via SPI.
Nrf is the master and AD7780 is slave. I am know implementing my solution referring to an example i found about SPI...
