Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
I'm registering two p_storage modules, one allocates 3 blocks of 16 bytes (so one page to my understanding) and the other one 512kb ( 5 pages).
to my understanding,if I...
Hi everybody.
I am making an application using ANCS, I saw that the original ANCS application saves some data to flash memory via device manager module and the parameters...
Is there a way to get to an softdevice/radio event, which is generated every time an advertising packet is send? I need to set a pin in high state while sending a packet.
Hi,
In my application, I am using nus service with S110 V7.1.0 (nRF51822). I faced to one problem that the rx channel is set up to notify characteristic. In iOS (8.3),...
My question is while the application is running, how can I disable the NUS service to turn on the DFU service. This idea stems from this question: devzone.nordicsemi.com/...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I've testing a Raytac mdbt40 module and I'm running the ble uart example (sdk 9.0, gcc debug enabled, no gcc optimization) and no external 32khz crystal
I can scan and...
Hello,
i would like to update my SDK to SDK11, but i'm not sure that the pack installer in keil works..
What are the different versions of the pack?
I 've this one...
Hello All,
The compatibility matrix states that the sdk for rev 2 devices has been discontinued on version 6.1.
We have some other products with rev 3 devices where...
Hi!
I'm using nRF51DK with s110_nRF51_8.0.0 Soft Device and SDK_9.0.0.
My application reads ADC with frequency 500Hz (2 bytes of data from one sensor each read), and twi...
I am just wondering about the status of nrf52 support for the mbed platform (specifically as a yotta target).
I have seen a number of other threads on both the nordic side...
I am developing an application on a STM32 CPU that uses a 51822 through BLE serialization for BLE connectivity.
I have connected some LEDs at the pins of the 51822 to indicate...
Hi,
The nRF51WLCSP needs IR blocking coating and I found here that an example epoxy can be Epo-tek 320. I just want to check if there is any specific time for covering...
Hi
I have been able to successfully write using FDS but I'm unable to read back using the same keys. Here are my code snippets:
#define FILE_ID 0x1111
#define REC_START_ID...
