I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
I am developing a power aware TWI driver for 51822/422. All appears to work properly except when I simulate a bus fault by shorting SCL to ground or shorting SCL and SDA together...
Hi,
Firstly a warning I'm a noob in this area.
I'm seeing some strange events consistently returned from the nRF8001 over SPI. I have an example of the SPI traffic below...
Hi! I would like to get adc sample from two different channels at the same time on my beacon (nrf1822), using the same interrupt. Is that possible?I mean I can use ADC_IRQhandler...
Hi,
It's a very simple question, is there a simple way to check GPIO pin status. I just want to know at a given time if the Pin is High/Low. I don't think I need an ISR...
Hi, I just started working on nRF52 with Bluetooth, and I have some concerns about DFU and security.
I’m working on a product equipped with an nRF52 and a MEMS microphone...
Hi!
I am using the NUS service and I noticed that Android 6 (Marshmallow) will not go faster that 47.5 ms. Even iOS can go to 30ms. My target is 7.5.
Am I doing something...
Hello,
I am using nRF52832 with S132 and SDK_11.0.0. I am facing issue with using power fail warning POFWARN. below is my code snap.
void POWER_CLOCK_IRQHandler(void...
Hi All.
I'd like to know how to turn off or on shockburst feature.
After I set auto ack & retry count, Tx successful interrupt occurs, even though receiver device is in...
I'm migrating an app from SDK8 to SDK11 and I'm getting errors using TWI to communicate with my IMU (Invensense 9250). I first tried it on a nRF52 DK (Eng B) and then went...
I've either got a bug in my code or the JLINK connection is dying. Either way it's a real headache to pinpoint and discover how to resolve. Knowing more about extracting info...
Hi, Now I use the NRF51822 ADC to sample VCC , 1.2V internal reference，internal prescaling 1/3.The PCB connection show as the pictrue .My application develop base on soft...
Hi,
I would like to make some measurements via I2C in radio_notification_evt_handler. Unfortunately, after executing a random number of measurements, the advertising stops...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
Hi,
I am wondering which frequency tolerance is acceptable for the HFXO, as in the product specification, p.105, a maximum value of +/- 40 ppm for Bluetooth low energy...
