Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello!
nRF52832 IC supports programming OTA the first time after its soldered onto a custom design?
We are designing a very small form factor wearable product and would...
Hello all,
I have a few questions about the best way to go about mass producing nRF51822-based devices.
Can anyone recommend a manufacturer that possesses the...
Cruising through a few questions about the ISP, In System Programming, in the forum and in both the specification sheets, 1.0 and 1.1 there is no clear documentation to the...
Dear Nordic members,
I am currently trying to measure the power consumption of the nRF52832 with the nRF52 DK. I am very new in the evaluation and testing of BLE Chips...
Hi
I am trying to implement long writes on the gatt server side. My implementation is stack handled, so I am going for the " GATTS Queued Writes: Stack handled, one or...
Hello,
As a power source I am using a battery with an open circuit voltage of 3.67V.
The specification states that the recommended absolute maximum supply voltage is 3...
Hello,
I'm trying to make a communication with a nrf51822 and an trf7970a nfc reader. The communication is based on SPI, I read that there are problems with softdevices...
Hi there..
I need central device simulator to test my UART App.
Is their any facility available for Nordik UART peripheral simulator like ANTware in ANT+ wireless protocol...
Hi everybody,
we have implemented DFU with button and it works like a charm. Now we want to improve that and implemented the buttonless version too. Though, instead of...
There was an Arduino ANCS library released for nrf8001. Seeing that Arduino Primo nrf52 will be coming into the market and knowing that there is Arduino nrf51/nrf52 core development...
hi.
i open ble_ant_app_hrm from sdk 9 and i send data over ant .
how can i send a data just one time cause i want save it on eeprom.
how can i send a data just one time...
Hi,
I noticed a bug in ble_ancs_c.c where it will write NULL-termination outside the attribute buffers added with ble_ancs_c_attr_add(). When the received ANCS notification...
I got a hardfault crash in the ANCS code, when an invalid ANCS notification was received from the phone: attr_id_parse() read 195 as attr_id, and used that as index in ancs_attr_list...
When one host and one device,the through can be 16KBps。But,when one host and two device ,the Max throughput is only 6KBps。Can you tell me Why ?????And Can you tell me the...
