Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hello,
I had this compiler error issue .
I know this dirty laundry shall be cleaned by Keil and Microsoft Windows. But you still can help if you add to your SDK project...
I have clone nRF51 mesh project(nRF51-ble-bcast-mesh-master.zip), and I can find BLE_gateway sample project in the zip file, but I can't find a led_mesh project. Does anybody...
In SDK 11, there was an immensely useful function known as NRF_LOG_PRINTF. in SDK 12, this seems to have been replaced by NRF_LOG_DEBUG, NRF_LOG_INFO, NRF_LOG_ERROR. However...
pin 2 is for turning on and off at sepecified time...
pin 3 is for turning on the light whrn button is pressed and turned off automatically as time decided in the program...
I have been debugging this problem for a few days and have exhausted all of my options. I am relatively new to embedded development so user error is not out of the question...
Hi,
I need to load ble code to mrf51422. I read on the forum that I can do it using nrf51 dk but did not get the steps. Couod someone give me detailed description about...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello to everyone!
I'm digging documentation of SDK. and I meet a lot of doxygen things like this
/**@brief Macro for configuring a pin to use a GPIO IN or PORT EVENT...
Hello Everyone,
I want to program the BMD-300 with the nRF52 Preview Development Kit.
I have connected:
BMD-300 -> nRF52-DK
SWDIO -> SH_SWDIO (pin #4) on P20
...
Sorry for probably stupid question..
All the time in SDK we set need bits through the mask, for example
NRF_GPIOTE->CONFIG[idx] |= (pin << GPIOTE_CONFIG_PSEL_Pos) &...
Hello,
I am looking to get started with NRF52. I am very familiar with TI BLE so not a beginner.
I am looking for a high level introduction to the nordic soft devices...
Hello,
i am new to BLE,
I am using the iot S1xx Softdevice on the nrf51 Dk in order to test ipv6 connection, and now i want to add advertising with the Eddystone protocol...
Sorry I am new to this. Therefore this question may seem to be odd:
I want to build a temp monitor using an nRF8001 (BLE Board Adafruit) and send this data to my mobile...
This is the code I am using to wakeup my system from OFF. It is not working. Kindly Help.
#define Pin_0 0
static void gpio_init(void)
{
ret_code_t err_code;
...
I am creating a system (nRF52 SDK11.0.0 s132) that will get a data ready interrupt on a GPIO (configured via GPIOTE with a handler) from a sensor every 4ms. The sensor has...
