Is there an AT command (For modem firmware >= 2.0.2) that can be used to validate whether the LTE modem can communicate with an external MIPI RFFE switch (for example on a...
Can Nordic share specific instructions on how to enable hardware tracing?
I've received the following patch from Tomasz, however I still see "trace clock missing" in Ozone...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
Hello,
We plan to use the Serialization mode with the NRF52832 module.
We would like to know how is handled the low power mode when the NRF52832 module is used in Serialization...
I am adding a bootloader with BLE OTA upgrades. I am using SDK 11.0.0 and I based my bootloader in examples\dfu\bootloader . I can only fit a single bank upgrade (I upgrade...
Use the guide to compiler the UECC almost neet use 20 hours to finish it.
I think that Nordic need provide the after compilered uecc lib.
That will save so many time...
I have an accelerometer that utilizes IC2 (NXP MMA8452Q) that I am trying to integrate with the nRF51 DK. The accelerometer is on a breakout board, and is wired up very simply...
I have successfully been using the MIO ALPHA heart rate monitor with S120 0.8.0-3.aplha and SDK 5.1.0, using the SDK application "ble_app_hrs_c"
Im trying to migrate to...
I develop with MDK.
Now, I want to create a bootloader with 12.1?
Follow the instruction of the document, I must install micro-ecc, and ....
But as last...
For example:
region 0: 0x00000 -> 0x1b000
region 1: 0x1b000 -> 0x40000
In region 0: the first page(1024 bytes) is 0x400=1024 from 0x0000 -> 0x400 , ERASEPCR0 must be...
When I change the target from nrf51422 in the SDK into nrf51822 there is this error in Keil uVision Project window.
I can't find a way to remove the files in red warning...
Hello,
I have a problem with secure bootloader.
what I did:
Flash SoftDevice 130 using nRFgo Studio.
Compiling \examples\dfu\bootloader_secure\ (i removed the...
Hi guys,
I'm following the tutorials in devzone.nordicsemi.com/.../
I'm in the final step to show the GPIO in peripheral views, but there is no modules in the view....
Hi,
I´ve been reading a lot of question about the duration of the SOFTDEVICE_HANDLER_INIT, and I've found that if a change the accuracy of the calibration it will be faster...
Hi,
4.4.2 is known to have lots of BLE problems.
Is there a summary of the main known problems regarding BLE that have been fixed
in 5.01
in 5.1
.....
In general...
On dev kit nRF52 PCA10040, rev 0.9.0, Keil uVision 5.21.1.0, SDK nRF5_SDK_12.1.0_0d23e2a - I need to monitor 9 input signals for a transition (hi to lo) on any of the pins...
I'm trying to program a nRF51822 custom board using Debug out pin P19 of NRF51-DK through Keil MDK, here is the problem I encounter:
To simplify I just use the simple blinky_s130_pca10028...
Hi,
I'm developing simple bluetooth app, where I'm using 3 custom services, each one has characteristic with notification option.
But only the first service notification...
