Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hello,
my program should do the following:
Collect sensor data
Initialize SD and start advertising
After a timeout or after a successful data connection it...
Hi, Nordic
I want to change usb in/out packet size after hal_usb_init().
as I know, it should make one report descriptor and update.
But I can not see similar demo...
My latest assignment is adding NFC functionality to the device (the very same device that I had trouble with DFU on). Adding the functionality was easy enough but I'm having...
I have seen this topic:
devzone.nordicsemi.com/.../
and a few others, in an attempt to visualize the RAM usage of my project. I currently use GNU ARM Embedded (gcc)...
Please clarify the radio state diagram for the nRF52: it shows a black dot between TXIDLE and RXIDLE states, having arrows from TXIDLE or RXIDLE leading apparently back to...
Hi guys!
I wanted to ask that can we use an external flash(connected via SPI/I2C interface to the mcu) instead of internal flash for storing downloaded image(s)?...
Background: We use NRF52 chip along with SDK 12.1.0. Since we have a few components of firmware (i.e. secure DFU settings, secure DFU , application, Softdevice) that go into...
The aim is to use the nRF51822 chip beside the application processor and to run the soft device S130 in it but as I saw, the newest SDK v12 supports only S132 Connectivity...
I am trying to update my S132v2.0.1 devices over the air to S132v3.0.0 and am getting no bootup, even after swapping dfu_dual_bank.c from the answer below.
devzone.nordicsemi...
I am studying this tutorial: nRF52 Online Power Profiler . I know this tutorial basically related to the ble_app_pwr_profiling example in the SDK: Power Profiling Application...
Hi, Nordic
I know pipe0 and pipe1 are be enabled on nRF24LU1 nRFgo SDK example for default PRX.
Now I only to enable pipe0, disable pipe1.
First, I use this...
Hi, Nordic engineer
nRF52832 as ESB PTX, nRF24LU1 as ESB PRX
same channel, crc, and match address and pipes, but from nRF52832 uart log, ESB TX fail event always show...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
Hello everyone~
Although one TWIM interface of the nRF52832 can "interconnect up to 127 individually addressable devices", I still think that use different interface will...
