Hi
I am using nrf70-wifi-ble-image-transfer-demo in the nRF7002 DK.
I change nothing on the code form the sample, after patching I have succesfully build the code and...
Hello, I wonder if it is possible to run the Thingy91 in MQTT-S with a certificate system to ensure the connection between the broker and the thingy. (CA, device certificate...
Hi,
I am currently building software on NRF 52810 and softdevice version is s112 7.0.1. I have one service which has three characteristics. When I add either a new service...
Device Information
Module: FANSTEL BC832 Bluetooth Low Energy 5 Micro Module
Chip: nRF52832
Firmware version: Default AT firmware
Current MAC Address: ef30:0a:cab132...
Dear Nordic Support Team,
We are currently exploring the use and potential benefits of the paEventCounter as described in the Bluetooth Core Specification 5.4, Section 4...
Hello!
Since we are moving from the prototype phase of our project to the pre-production phase, we have developed a custom board which utilizes the ISP2454, nRF54L15 SoC...
Hi,
I am working on Temperature sensor MAX30208 using nrf52840 using zephyr. i am working on ncsv3.0.0 . I want to develop a driver for max30208 . can anyone guide me how...
Hi there - new to Bluetooth but have an interesting question.
Is there a way to have multiple users connected to the same Bluetooth connection to stream music? For instance...
Hi community,
I am working on IoT device. We want to establish a secure connection therefore we are going to need a secure storage for our private key. I am aware that the...
Worked fine until yesterday. Board turned off with computer, also the power switch on the board was in off position before turned on this morning. Now the debugger circuit...
Hello Nordic Team,
Please, I would like to ask some questions about BLE based smart-phone accessory.
Actually, I think about using a BLE based accessory (for instance...
Tuning the nRF24xx matching network:
The balun-function is done by the
180° degrees phase shift in L1. This
causes the signals from the two ANT
pins, 180° out of...
I am sending IMU data as 20 byte packets through nus service at the rate of 50 such packets per second. The device is a nrf51 DK configured as ble peripheral (S110). The application...
Hi all,
I have a makefile which runs perfectly from the command line on Windows under GCC, but in Eclipse it fails with this message in the Console:
make flash
make...
My application had a ID to separate difference device & host for the communication in the same area. When the Host power up, it need to search any existing same ID Host nearby...
Hi ,
I want to set the channels used for exchanging DATA (after connection) when peripheral and master are connected.
i searched and i find that it's like this :
//Set...
Hi I'm using the PCA10003 dev board to try it out the OTA firmware update.
What i did is exactly that:
Modify the bootloader example for S310 softdevice and 10003...
Hi, I have been developing with the nRF52 DK for the past couple of months however I have encountered an issue today which I am unable to resolve.
I am unable to establish...
Continuing my mission to have SES set up to be the complete development environment on a Mac I am struggling to get the Jlink Debugger to behave with SES.
It appears I...
hello , I want to Know how to write value to S0 , L ,S1.
for example : I want Set S0 =1 , L = 16 , S1 = 1 .
but I can't find any register to set S0 , L , and S1. .
My...
We are trying to reduce standby current consumption for our application. When measuring the current depending on the environment temperature we can see a rapid increase of...
My Application will have 4 difference host in the same area, if one device send a data and receive the ACK payload, is it receive all of the 4 hosts ACK payload or one of...
