Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
As title ,
I try to add the NUS service that show on the ble_app_uart project into Multi-link project.
But it doesn't work .
I want to a central connected to at...
I want to use PWM on only one output pin. I'm using a nrf51422 and softdevice s130.
I want to be able to set the PWM and then change it again (a sequence). This is to be...
I have tried using the pre-built nRFUart Example in the Master Emulator API (2.1.11.1) and get the above error
I also tried rebuilding - no change.
I do have a PCA10000...
Hi everyone,
I'm seeing a weird issue with one of my two instances of 2ch PWMs where if I receive data from TWI, my PWM1 stops functioning and TWI stops functioning as...
A characteristic can be read/write/notify.
I have seen cases in Nordic's examples where there is an internal boolean "is_notify", and when the user sets it from the central...
I'm using an nRF51822 on a custom board with Nordic's serial DFU example from SDK v10.0.0. I'm trying to find a way to exit the serial DFU without the DFU trying to update...
Hello,
I wanted to know if is any way of changing the Pins for the UART and still get the data through the USB connected from the PC to the DK? Or do I need to always physically...
Hello,
I am stitching together two examples in nRF_SDK11:
I started with example
ble_app_multilink_central
The I added code, includes, to main.c and...
Hello,
I've got a problem, and I don't know what is happening.
I've programmed several nRF51822, and my program doesn't works until I connect the debbuger to nRF51822...
I'm interested in creating a bluetooth dongle that defaults to a hid proxy mode in a manner similar to a number of csr based dongles.
What this means is it presents itself...
In libuweave project there is an example demonstrating communication between nRF51/52 and android client app. The Android client application is named SimpleLock.apk. But I...
Hi
I am trying to use nrf51822 as both peripheral and central device for my application.
nrf51822 as peripheral checked satisfactorily with a smart phone as central device...
Hello,
I use EV-board PCA10040 and run I2C demo on path nRF5_SDK_11.0.0_89a8197\examples\peripheral\twi_sensor\pca10040. I measured the current over 5.7mA .if modifing the...
