I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
I use the nrf52832 with softdevice S132 s132_nrf52_1.0.0-3.alpha for a ble application.
without the softdevice, the rtos works correctly.
but when I enter this parameters...
I'm moving from nrf51 to a higher performance uC. I think that there is lot of models of nrf52.
what's the reference of the best nrf52 in term of performance. I want to...
I've been using the device firmware update service for quite some time now. I'm looking to add the ble_nus service, but this feature seems to fail when ble_dfus is re-enabled...
With the latest nrfjprog from Nordic and latest J-Link software from Segger, I am still getting the error below.
$ nrfjprog -v
ERROR: JLinkARM DLL version used is too...
I am working on the ble mesh using nrf51822. I am able to read the mesh values using the nrf master control panel android software. But we want to make an android software...
the priority of my custom thread is lowest priority. but it's not possible to call hvx function.
in ble_app_hrs_freertos example,
a sd_ble_gatts_hvx function is called...
Hello,
Suppose I flash a device that uses the nrf52832 with a serial bootloader, SD and valid application, can I still write to UICR regions via a serial connection using...
The nRF UART Android app currently uses a non-monospaced font; so, for example, a '1' is a different width to a 'W'.
This makes it hard to view strings where the fields...
Hi. I'm beginner.
I want to use nRF51822xxAA chip on keil compiler.
project->Option->Target->IROM1 start, Size & IRAM1 start, size.
Please let me know IROM's start and...
Hi,
I'm using ble_app_hids_keyboard example as the base to develop my own application, but was found something really strange, the application seems never get into sleep...
Hello Nordic!
I am using an Android phone and a nRF51822, and I'm performing BLE speed tests.
For these two devices the theoretical maximum is given by 4 * 20 / 0.0075 ...
So I have a remote, a central, and it's connected to my peripheral.
The remote is based on the multilink example.
SDK V11.
I want to press a button on my central and...
Hi, i'm wondering if it's possible to make a GPIO pin trigger different tasks when it is externally driven from low to high, and high to low.
I'm trying to stop an RTC...
