Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hi,
I'm trying to config my device with resolvable private addr (RPA) as code below:
rpa_add.addr_type=BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE;
sd_ble_gap_address_set...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Dear Nordic Developer Zone,
In order to synchronize some tasks (motor-driving), I have recently implemented the radio notification interrupt.
In this interrupt, I toggle...
Hi,
After following all instructions on: gnuarmeclipse.github.io/.../
And after installing all Nordic Semi dependencies on eclipse.
I import on eclipse the UART_Loopback...
I'm trying to interface the twi driver with a ft200xd chip (i2c -> USB serial). I want to read the available bytes, but it requires a general call first see page 29 of www...
Hello everyone!
I got one question and could you guys help me out?
When I open the nRF Connect Mesh, after I program successfully, I can't initialize selected device while...
Hi, I'm working on a cross-platform application that needs to communicate with a custom peripheral (nRF51822 with S130 v2.0.1). I've implemented the interface for both Linux...
Long time reader first time poster upper.
I am working on a very minimal BLE send / receive scheme for a research project, and am not using a SoftDevice. I have written...
Hello,
I am noticing something curious when I attempt beacon mode for my nRF52 (sdk 12.1). Attached is an image of ubertooth packets that correctly show my ADV_NONCONN_IND...
Hi,
I am trying to communicate to PCA10040 (nRF52) dev board to communicate.
Basically i want to configure 1 board as Master another as slave, so master will initiate...
Hi,
I am using SDK 11.0 for my project development. When I tried to compile the unaltered SPI example given I got 60 Errors in my laptop. The Same SDK in other laptop is...
Hi all,
first of all I'm new to NRF and BLE applications so I'm truly sorry if some of my questions are very basic and if answer to some of them is already posted somewhere...
Hi all,
I am using pins P0.00, p0.01, p0.09 and p0.10 in my application. I wandering why these pins are not functioning as GPIO. I have searched various links such as ...
Hi，everyone！I am using nRF connect mesh for Mesh DFU(see this link text ), and I follow the direction step by step. But, the nRF connect can't find any device to program....
Hello,
I am trying to implement a Heart Rate Monitor Interface (HRMI) board with my nRF52, using the TWI_sensor example from SDK 12.2. I am running into trouble Writing...
