Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
I'm trying to use BLE library for python to communicate with one Nordic nrf51844 chipset. Because one characteristic is notification enabled, I need to enable notification...
Does there exist a white paper describing some typical PPI use cases with coding examples? The only one I've found is the peripheral/gpiote example and it is severely lacking...
Updates are moved to the end of the question
I created a modified version of pca10028.h and boards.h and have preprocessors changed so that the following new config is...
I example test ble_central and ble_peripheral of ble_app_uart.
Radio TX and RX test is OK.
It confirmed the data communications relating to uart_event_handler function....
I'm trying to get a time stamp using app_timer_cnt_get(&ticks), but the ticks always equals 0. And I have called APP_TIMER_INIT() to init the app timer. I have no idea why...
Hi everyone, I have been given a nRF51-DK board and I should use it to send data retreived from a sensor to it through Arduino, to finally receive it in my cell phone. I am...
Hello everyone,
I'm brand-new here. I have developed quite a bit of software on desktop PC's, but this is my first experience with embedded programming. A few weeks ago...
Hi Team,
So I downloaded the new nRF Connect for OSX. I inserted my PCA10031 nRF51 dongle into my USB port and the relevant lights lit up. However nRF Connect does not...
I am quite new to embedded firmware development and definitely just two days old into Nordic nRF52 development.
I want to just setup a 25% duty cycle clock output on GPIO...
Hi,
I have a very sophisticated program on nRF51822 with SD120 which uses SPIS (as an RX for another board) and UART. I used "spi_slave_example" as a base program.
I am...
Hi, in the (not great) mBed PWM driver, when setting up GPIOTE to toggle the output pin they do this:
/** @brief Function for initializing the GPIO Tasks/Events peripheral...
Hi,
I have a application that needs to advertise only for 120 seconds and on change in values of accelerometer , it needs to start advertise again.
presently i have a...
Hi,
I've been using these parts for a few years (the 51) and recently did some work getting the boot loader to be joined together with the application into a single burnable...
Hi,
I wish to exchange the sensor form mma7660 to hmc5883l, so I simply replace it with my own function just like mma7660 did.
Those function are
define HMC5883L_ADDR...
Dear All.
As I know, nRF52 support PDM mic. So, I'll make recording sound with nRF52.
But, I do not find PDM example on SDK 11.
Please notice me, where is the PDM mic...
