Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Hi all! I have a smart beacon kit rev 1, with s110 on it (the latest firmware available). I am using the RTC with the 32 kHz crystal (50ppm) to trigger an ADC conversion every...
After releasing reset to the nRF51, its UART is responding with
RX: A4 1 6F 1 CB
Further requests for things like capabilities, etc go ignored, and opening a working...
hi all,
i cant able to find the version 11 softdevice hex file. can you please send the link.
and can i use the version 8 softdevice for version 11?
-Thanks in adv...
In the migration guide, I can read: "Clearing an interrupt event may not take effect immediately."
And an example of required code is given as:
NRF_TIMER0->EVENTS_COMPARE...
I'm creating a PC application using the ble windows driver by nordic, i cannot implement white list. I ported my code on the firmware & it works.
Is this a limitation of...
When i follow the Getting Started guide for the nRF52 DK at point 5 the led (led 1) does not start pulsating and I do not get contact with my phone. I tried to upload the...
I am trying to make communication between STM32F407ZET6 and NRF52832 chipsets using an SPI interface.
One is master and another is slave. If I take NRF chip as master,...
I am noticing a problem with pstorage_raw_clear when called in the DFU code. My problem is this: when attempting to update an application, if the application is too large...
HI, I have a remote control with nRF24L01. It was talking with Gen1(uses nRF24L01) product via ESB. Now, I am developing Gen2 product*using nRF51822xxaa) and I need to support...
Hi,
i'm doing my own bootloader and i want to use external flash to download image trough a spi. The bootloader project based on example from SDK11, now just an external...
Hello:
It appears (although I am not 100% certain) that there is a small delay (< 10 usecs) between EVENTS_END in the radio and MICSTATUS in the CCM. I believe I have read...
Hi,
I've got an application running on an nRF52, and it's calling sd_app_evt_wait() from the main loop - and it's staying in that function pretty much all the time.
...
I don't have a 32KHz crystal on my board (using the stock Rigado module) and power isn't an issue as the board is mains powered in operation, so I was intending on using the...
I found a alpha version of softdevice v3.0 (s132_nrf52_3.0.0-2.alpha.zip), and it supports MTU_SIZE > 23 bytes, but there is no SDK (current version is v11) supports it. When...
We have two nRF51822 chips with cleared contents in FICR, e.g. addresses 0x10000000 - 0x100000FF are 0xFFFFFFFF.
UICR works as expected.
Chips execute code.
Radio performance...