Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have to connect more than one nrf-51822 dk and send theirs RSSI level, because i need to knows their posittion. Somebody could help me? Have some example similary to what...
I am using the nRf52 device with FreeRtos and SD132 version 11.0. The configUSE_TICKLESS_IDLE is set to '1' to allow the device to go to sleep. After the OS is started - there...
Hello Nordic users and employees,
I'm having a small dilemma. The device I'm building runs on the nRF51822 and needs to store a small number of bytes off to the side and...
Hello, it is to my understanding that profile & service do not have fixed forms. Services make up profiles and you can choose how many and what services make up a profile...
I I'm running the ble_app_blinky example under pca10028 on the nrf dongle pca10031 using sdk11. The dongle disconnects after 24 seconds. Can anyone point to me what is the...
A typical classic or BLE get paired with the phone/central, and normally the central can decide to forget/unpair it. In this case, the device (nordic chipset) which previously...
I had created application with enabling the UART service(as in Ble_uart_app example) and tried to update the Rx characteristics of UART service in connectable mode through...
I'm sending a write authorization reply using sd_ble_gatts_rw_authorize_reply() in response to a standard Write Request with one byte of data. When I set the gatt_status to...
I am currently dealing with a strange problem when trying to use DFU OTA. When I enter DFU mode on Master Control Panel and try and update I get the following two error messages...
Does anyone have a working copy of ble_cps.c\h
The BDS (version 1.0.2095.0) plugin (v.1.2.4) does not generate code that compiles under IAR EWB
IAR ANSI C/C++ Compiler...
Hi there, I'm definitely a newb when it comes to wireless communication and communication protocols so I'd like this question to be answered at a higher level than what I...
Hello,
I am implementing a central which is scanning for advertising packets using s130, SDK11, nRF51822 and based on example ble_app_hrs_rscs_relay.
I get the advertising...
Hi,
I'm trying to porte my code from micro_esb to nrf_esb. My need is to know when a frame with correct address is received. This frame don't need to be valid just received...
Is there any way to use more than 4 buttons using app_button or BSP library?
It seems that GPIOTE can handle only 4 pin. Am I right??
uint32_t err_code;
// Button configuration...
