Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
I have some questions about the scan response packet.
Can a scan response be sent with a peripheral that is configured to be connectable? IE not a beacon.
I read...
Dear Nordic Team,
Thanks for support.
I am using nRF5_SDK_11.0.0. How can i initialize the softdevice with internal RC oscillator in my source code. I am using the below...
Hello;
I'm trying to get data over the TX pin to be sent to the RX pin on a Raspberry Pi.
I have it working on several boards: The nrf51822 Development Board, the Redbear...
The radio notification tutorial ( devzone.nordicsemi.com/.../) says:
"The distance is the time window before/after the radio goes active. The radio events are radio_on...
I'm slightly bamboozled by the LFCLKCSRC options in the NRF52 datasheet / product specification.
Bit field SRC makes sense. Set to 0 for the internal RC oscillator, 1 for...
Hi
I am currently using the boot loader from SDK7.2.0, compiled using Keil.
However, for all the other software I am using GCC. But GCC support for the boot loader was...
Hi, i am trying to send my notify characteristic every 100 msec, i am using timer for this and when i am connecting to the nrf app, my nordic device is sending the data but...
Hello,
Thanks for your reading.
I tried to read the CHIP_ID value(0xD1) of BMI160 in MetaWearCPro firmware using SPI.
But I could not get the correct value(0xD1). The read...
Hi, I use the following.
Raspberry Pi 3 (RPi3 with Raspbian Jessie 4.4) as a router,
RPi3 is connected to a Wi-Fi router to access the Internet by using the built...
My development Kit is official PCA10040, and SDK is SDK 11.
when i opened the keil project of ble_app_multirole_lesc int the examples of SDK with Keil MDK5.14 and compile...
Hi,
I've got a nice, well-documented bug here:
github.com/.../25
The short of it: Adding a single printf() statement to this mbed OS example causes my nRF51-DK board...
Hello all I am new Nordic and Bluetooth, before starting my project I did small experiment to understand the system i did the following steps.
Used nRF51822 -32 KB...
Hi all ,
I used SEGGER Embedded Studio v3.10 , and import a ble_app_uart keil project , but now build warnning as follow:
create .elf file have a warning "cannot find...
I'm using a nrf51422 customised board. I want to push the firmware to Bootloader mode via ANTware using a payload. But if i use graceful shutdown, the application malfunctions...
Hi, i used sdk11 and softdevice version s130_2.0.
And i used pwm library.
i try to make pwm pulse accurate 38khz.
When i used sdk 6.0, i could control timer used...
