The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
I'm developing a new board with nRF8001, after reset i correctly get the DeviceStartedEvent 0x03 0x081 0x02 0x00, after that i go into setup mode sending the configuration...
Hi,
I am using nRF5_SDK_11.0.0_89a8197 at center to debug ble_app_uart_c project.
The center can connect the device well at the beginning. But if I power on and power off...
according to the introduction of mesh framework( value storage part), it says all mesh data is saved in a structure. My understanding is : Handle means a trickle instance...
How to configure S130 Softdevice as Completely Central(S120) i.e with Out Switching its mode to peripheral to operate like a central.
Is there any API or Example to do...
For example, if the first page is erased then it will set this page as swap page and continue looping without increasing the 'page' variable.
This means that the last...
Hi,
I have flashed boot loader to 0x7A000 (Size 24kb) and Softdevice to NRF52 DK ,then flashed application using nRF connect .
Am also able to update application after adding...
Hi,
I need PWM on 2 pins, with a varying duty cycle, and read some posts in this forum on the subject.
I am still using SDK7.2.0, with SD7. Our product is stable, so I...
Hello, a few days ago I was having trouble with RF performance on a custom PCB using the NRF51822. I posted here to get feedback and figure out where the design went wrong...
sdk : v8.1.0
os : ios
tool : nrf tool uart
use the ble_app_uart, it worked normaly. and add duf fuction in the application by the notice
[http://developer.nordicsemi...
Dear all
I found that the frontline BPA sniffer can't catch the connection data between Android5.1 or ISO and BLE device. Does this normal? How can I use the sniffer to...
Hello, I have to implement infrared sending and receiving of a modulated signal in pre-existing code.
I have managed to implement infrared sending thanks to the ble_app_uart_IR...
Hi!
I have creat two timer with app_timer_init.
start the first timer trigger every 4 ms, every 125 times(approximately 0.5 sec) to start the second timer which trigger...
I am having issues using the correct definition for the clock config:
for
nrf_clock_lf_cfg_t clock_lf_cfg = NRF_CLOCK_LFCLKSRC; SOFTDEVICE_HANDLER_INIT(&clock_lf_cfg, NULL...
Hi,
I have very trivial question. I open the template program which is attached in SDK 11.0. In application timers start function I wrote the following code. The result...
I am only sending the local name in the BLE advertisement packet. Do I need to send the manufacture Id as well, even if there is no manufacture specific data that I need to...
