در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hello Nordic,
I just read the news from may about the arduino primo and i am really exicted!!
I have been tring to decide between arduino due, or some complex ensemble...
I'm developing an application on a custom nRF52 board. I have no problem to program the board with Keil. However when I try to program the application with the nrfjprog, the...
Hi all,
I have been porting a project from SDK 8 to SDK12, andi have ported one of the services, however when i add a characteristic it throws
:ERROR:From File error...
Hello,
in my current project we develop a BLE firmware which runs on a custom board based on a Telit +s42 module (with integrated nRF52 SoC).
We are able to flash the...
Hi,
I am a bit confused from the example, in the specs it is said that writing the flash is word allign, and even so the example does something strange:
do
...
hi.
this is my code that i copied from ble_app_hrs_rtx .
osPoolDef(ble_evt_pool, 8, ble_evt_t); /**< Definition of memory pool for ble_stack_thread */
osPoolId ble_evt_pool;...
The ShockBurst bitrate mode ( nrf_esb_bitrate_t ) NRF_ESB_BITRATE_1MBPS_BLE is described as '1 Mb radio mode using Bluetooth low energy radio parameters.' in the SDK documentation...
I've recently updated the hardware on a custom board, moving from the nrf51422 to the nrf52832 and migrated the code from SDK9 to SDK11. I've got most of the functionality...
Hi. I'm using nRF51822 and SDK10.0.0, S130 for Central BLE.
I want multilink as Central.
As I know nRF51822 supports Max. 8 peripherals at the same time.
I can connect...
When using the sniffer to analyze GATT exchanges that use attributes > 20 bytes (which means L2CAP packets with fragmentation), the Wireshark tool does not show correct information...
hi.
i get a lot of information on Bluetooth and i want send it to 16 slave via ant.
what is the best way to send information over ant considering the speed of Bluetooth...
I have run into two SAADC issues on the nRF52832 using SDK v12.1.0. Any recommendations on how to fix them?
Issue 1:
When the Keil compiler optimization is turned up...
