Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
HI ALL,
I want to obtain the status of the upgrade process using mcuboot ble, such as flashing lights when starting the upgrade, flashing lights during the upgrade, and...
Hi,
I am working with the nRF54L15 and I want to use it both as a BLE central and as a BLE peripheral. So, I have two separate source files: one for central and one for...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
Hi
Our present build system on v2.6.1, builds variants of our baseline application using batch files.
It ends up building using west in this way:
The generated...
The nrf_cloud_multi_service sampe is running in to fatal error while trying to downolad A-GNSS data. The sample is configured to work with NB-IoT and CoAP.
Here is the log...
Hi.
I develop an application in the past with ARDUINO and a nRF24AP2 module with great success. I can read 8 heart rate monitors ANT+ sensors in the same time, with 8 differents...
I am a newbie in embedded programming. I want to encrypt some advertising data using aes-ecb API, provided by the softdevice but I am not getting any encrypted data after...
Hi,
We are currently using SDK 10 experimental boot loader example. We would like to encrypt the firmware before creating the zip file for OTA. The procedure we followed...
Hello everyone,
I am trying to use BLE module on nRF51 in central (oberserver) mode using IOT Softdevice. I want to scan for any device around my board.
I get error when...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Hello All,
I am interfacing WS2812 RGB ringx16 with nRF51822 and use nrf51-neopixel library from github.com/.../nrf51-neopixel
Its not working.
for example : value...
Hello,
I was looking into Gazell and read that Gazell only allows pairing when Host and Device are in close proximity to each other. This range is about 30 centimeters...
I'm trying to maximize BLE throughput between a central and peripheral (I'm programming both) running the new s132 SoftDevice v3.0. I can't achieve the maximum data payload...
I am trying to use the NRF51 dongle (PCA10000, firmware ble-sniffer_nRF51822_1.0.1_1111_Sniffer.hex) with the sniffer software but on selecting a sniff source and starting...
Hey,
I successfully build and load the ble_uart_pca10028_s130. Now i want to edit something to the Code and this error is shown up.
I think I have to include something...
Hi there, I have done search and know there are several similar questions, but unfortunately I didn't find any useful answer after carefully reading through them, thus I decide...
Hello,
I've just read the thread explaining the UART baudrate register settings. I then looked at the nrf52_bitfields.h file and found that the baudrate register values...
Hi ,
We are using Nordic SDK for our development and we have done some changes as per our requirements in the SDK . We are going to share the same with our end customer...
Is there any BLE chip under development which has lesser IO pins, as I feel most of the IO provided are underutilised.
I may be wrong or there might be technical issue...
hi,
i have a requirement to connect two nrf51(PCA10028) boards to connect each other.
1).if i turn on the Board1 should scan the bluetooth devices if any other bluetooth...
