Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
What does error code 4 mean?
I am looking through the documentation for the error code number to string translation.
Why is starting a timer causing the error code 4?...
I am trying to sample the ADC every 2ms. I notice lots of slowness with BLE advertising and typically can't connect to device over BLE when sampling. I am using PPI, configuring...
Hi
I'm trying to run the HRM_RX exemple on the nordic NRF51422. This is my configuration:
-Eclipse IDE
-ARM GCC 4.8.3
-NRF51422_AAC0 so I'm using the lasest SDK 4...
hello,
i am trying to use the example for the ble_lbs from github.
I get no erros on compile and flashing.
But wenn i try to see the device in the master control panel...
I've been slowly and incrementally adding changes to the ble_app_multilink_central example from nRF51-SDK-6.0.0. This is an exercise to understand where my other app stopped...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hello everyone!
Firs of all consider I'm very new in micro controllers programming/debugging, so your patience would be much appreciated.
I have a nRF51822 mKit like...
I use multilink_central example and try get information about discivered service:
APPL_LOG("[CLIENT_LOG]: Count of services: %d\r\n", p_client->srv_db.srv_count);
APPL_LOG...
my led connect whit a pin like this:
the led positive connect whit VCC and the negative connect whit a pin through a resistors.
when I config the pin as a output like...
using the nrfGoStudio to program s110_nrf51822_6.0.0_softdevice.hex
Tools:
Jlink,SWD mode as the figure:
but there are some problem
1:we can download demo BlinkLed...
