Hi, we are developping a medical device that receives an audio stream from a smartphone. We have a custom board connected to a different DSP than the one in the nrf5340_audio_DK...
Hi! We're testing nRF7002 with the nRF7002-DK and NCS v3.0.2. CONFIG_NET_ZPERF=y has been added to the nrf/samples/wifi/shell/prj.conf, the rest is untouched. Running that...
I am using the nrf5340 on a nrf7002fk dev kit. I am interested in low power operation so I am measuring the power consumed.
I am running a simple app:
int main(void) ...
Hi,
I have a simple question about Bluetooth Channel Sounding:
Question: If I use BT_CONN_LE_CS_MAIN_MODE_3 as main mode (PBR + RTT), does it make sense to use sub mode...
Hello Nordic Team,
I am currently working with the NRF54L15-DK. I have successfully configured the simple ADC on AIN4 (P1.11) and am able to read the raw sensor values....
Hello Nordic Team,
I am currently working with the nRF54L15 DK and interfacing an occupancy sensor over UART. In my standalone application (non-Matter), the UART communication...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
Hi,
I'm planning to use a nRF8002 to transmit via BT the state of a pushbutton to a RFduino. I've my RFduino ready to receive data (and this works when paired to my iPhone...
Hi,
I'm trying to detect the nrf8001 by my Mac. My android device detects it, but when I search for it in mac, it's not detected.
I'm using this library: github.com...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I recently started working with the NRF51822 and PCA1001
I need to read data from MPU9150 accelerometer via I2C and transmit the results over BLE.
I connected the...
Hi,
I'm communicating ANT through softdevice ant event handler as follows:
err_code = softdevice_ant_evt_handler_set(on_ant_evt);
void on_ant_evt(ant_evt_t * p_ant_evt...
Hi,
I'm using PCA10003 board with nrf51422 chip with version E0 and tried connecting ANT with ANTware II software using the HRM example and it works fine on UART but on ANTware...
Hi,
I'm using BLE and ANT+ concurrently with nrf51422 and s310 softdevice. I'm using on_ble_evt for BLE and on_ant_evt for ANT+.
I'm using following code for advertising...
Hi,
I want to add a bit (about 100KB) off data to my project in Keil.
I need to work out where to locate it (to avoid my code and the S120)
I can't seem to find a memory...
Good morning,
I have taken a look to different information related to this topic but I'm still confussed about the way to proceed in order to implement the way of working...
I am trying to use the dynamic payload length feature, but I am not sure of what settings to use for the RX_PW_P0 - RX_PW_P5 registers. According to the documentation, for...
Hello,
We are going to use nRF51822 in our product.
Use case is as follows:
Connect with android/iOS phone and receive some configuration data.
Connect...
Dear Sirs,
I'm using nRF51822 EVKit and using example code "button_radio_example" for pca10001 device and measured current consumption on this PTX device and found out...
I just want to handle phone simple call event from iphone4s.
How can I do? Is there any other way to do this?
There are so many media key in hid profile, is there any...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
