Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello
I've been trying to create a simple BLE observer that outputs the nearby devices data onto the serial port using a PCA10001 board.
For this, I'm adapting the code...
Hi - I'm using the 51422 dfu bootloader from the nrf 6.0.0 SDK and it works fine with the iOS apps, I can send both .bin and .hex files to the device and it works fine. However...
Hi,
I am using nRF51822 evaluation kit. I want to develop GPIO isr (GPIOTE_IRQHandler) which can handle multiple GPIO interrupts. I have tried to enable the GPIOTE_IRQHandler...
Hi!
When using bootloader, I cannot update application data from Keil (for example for debuging), because after restarting bootloader is loaded and
!bootloader_app_is_valid...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
EDIT:
I'm using nRF51422-QFAA E00 and S310 v1.0.0, SDK - nRF51 5.2.0.
I'm starting HFCLK from externall crystal for ADC conversion. Since I have no SD enabled everything...
I was using the sniffer to get a trace of the ble_proximity example for the NRF6310 DevKit, and noticed some Attribute errors when the Master Control app attempts service...
nrf51sdk v5.2.0
I am adding ANT service to our BLE application
To begin i building the BLE application and bootloader with the s310 softdevice.
I have modified keil...
Hi,
I have updated my nRF51-SDK to the latest version 6.1.0. I'm using PCA10000 dongle, nRF6310, PCA10004 and Master Control Panel for Windows. I've programmed my nRF51...
ble_gatts_attr_md_t* p_cccd_md; /**< Attribute metadata for the Client Characteristic Configuration Descriptor, or NULL for default values. */
What's the default value...
Hi
I'm trying to set up a 1ms tick timer using TIMER_1. In other words: every 1ms, I have to increment a tick counter, and to perform several operations. When SD is not...
Hy
I m new for here, and i would like to ask for help for you.
I have a nrf51822 QFAAC0 development board, form chine PTR9018 with 16k oscillator.
I use SDK 4.4.1,...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
