Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I am trying to connect my msp430f1611 microcontroller with the nrf8001 bluetooth chip. I read this thread ( devzone.nordicsemi.com/.../) and it seems very helpful....
I have been trying to implement a SPI Master on the nRF51822 Eval board in order to read data from an Analog Devices ADXL345 3-axis Accelerometer. I chose to start with the...
Hello,
Firstly, the nRF5122 Product Specification v1.3 Section 4.2 says that TIMER0 is 32 bits wide.
However, other product specs seem to mention 16/24 bit timers, and...
Hello Nordic people!
I'm developing my first firmware on nRF51822 and I need help with BLE, profiles and SoftDevice S110 stack.
Application it's a speed sensor for bicycles...
I have nrf51422 dk. The boards I connect to 3.3V power and via jlink to my pc.
I use the JLink command line tool.
I can not access the chips. Erasing is not possible and...
Hi there,
I am using Eclipse and GCC (codesourcery) as development tools.
In the gcc makefile, once provided by Nordic with the "button_radio_example" are two lines...
Would the example github.com/.../require-encryption-5.1.0
compile without any extra configuration ?
I am trying to build it in a Keil uVision v.5.12.0.0, but I have some...
Hi,
I have an idea to implement BLE based access control application. I considered nRF51822 based Peripheral device & iOS application for central device
Both the Central...
We are in the process of creating our 2nd pass boards with following components to achieve good RF range>20 meters. We are considering discrete BALUN components and SMD Chip...
I see 5V pins on the schematic for the new nRF51 development kit. If I power the board via USB, I understand that 5V is regulated down to 3.3V for the chip. Is the source...
hi,
i'm gonna make 51822 enter low power consumption mode.Meanwhile it could be wake up by "GPIOTE_IRQHandler()"
1:Now,i know that "sd_power_system_off()" can make 51822...
What exactly does the PSTORAGE_LOAD_OP_CODE (0x03) mean? The documentation says ( online ) that it is an "Error when Load Operation was requested".
The code is pretty straightforward...
When I try to generate a log file by clicking Log File... in master control panel. The following error message comes up.
error_log_file.png
I would like to create a...
Hello dear Nordic community,
currently I am working on the NRF51822 Direct test mode (DTM). I tested the ble_app_dtm example and it works fine for me.
This means I can...
Hi,
I bought nRF51822 Evaluation Kit and would like to blue wire an external MCU( Kinetis Cortex-M) to talk to the SoC. It looks like the SoC on this board has many GPIOs...
