Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
Dear Sirs,
I'm using nRF51822 EVKit and using example code "button_radio_example" for pca10001 device and measured current consumption on this PTX device and found out...
I just want to handle phone simple call event from iphone4s.
How can I do? Is there any other way to do this?
There are so many media key in hid profile, is there any...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi guys,
is it possible to get the mac address of the connected device?
Didn't find anything in ble_evt_t ..
Thanks!
Edit:
Sorry, i found it:
its in the ble_evt_t...
i am new to nfr51822 and i am doing project on indoor localization in which i need to read the RSSI values of bluetooth. so how i read these values? and i have setup the evaluation...
Hi !
I would like to know if there is a nAN-36-like application that also implements the radio functionity.
I would like to send a raw radio message to other devices...
HI：
I use Bluetooth capture crawl data. I want to see the data in DEBUG in?I can not see Adv PDU Header among type TxAdd RxAdd PDU-Length data in the code, AdvA which data...
Hello
I am developing a health fitness watch using the nRF51822 System-On-Chip. I am interested in acquiring an organizationally unique identifier that can be then be implemented...
Dear Developers,
At the moment I'm writing some software to develop an Android App. I'm using nrf8002. When my app connects to the nrf8002, I'm able to read battery level...
I am trying to use the nrf8002 for proximity type application. Right now I have a prototype working with a speaker and LED and I can light up either one using an app. What...
Hello every boby,
I'm a newbie in PIC programming and I hope something could help me to start interfacing the nRF8001 with a PIC. My schematic is already done but I don...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi
I'm using the Eval Kit PCA 10001 V2.1.0 and Nexus 5 with new Android version 4.4.2. Connecting to the Eval Kit works just fine, but when i perform a service discovery...
I have an nRF51822-based peripheral using the SoftDevice 110 v7.0.0 and SDK v6.0.0. The peripheral uses two custom characteristics under a single custom service. I'm using...
Hi
I'm using sd_app_evt_wait(); to go into low_power mode.
For some reason it comes back immediately, but I can't figure out why.
If I call it a second time it stays...
