Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
We are preparing BQB test for our BTLE product now.
Could you please help confirm if you have the test command to make 51822 into the test mode and can be auto-testing by...
Hi, I'm developing a HID-device using nrf51822, s110 ver 6.0.0 and SDK ver 5.2.
I would like to hide the device from unknown centrals once it's paired. I'm advertising...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
I'm using ble_uart_app & master control panel v3.5 for debugging uart communication. when uart is sending data to host(master control panel side), suddenly, master control...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Hello,
i use the bond manager together with a own module to store data in memory. On user interaction i want to delete the whole memory. I proceed as follows:
Disconnect...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
I am using the eval board, sdk v5.2.0, s110 v5.0 and a galaxy nexus with the UART Nordic app. I have not been able to receive any data on the android end. After
void nus_data_handler...
Hi, I am very happy to find that S120 can be implemented to realize BLE central role.
I start from the ble_app_multilink_central and ble_app_hrs_c --two experimental examples...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
How do I prevent drive by wireless hackers hijacking my ble device with their own dfu ota update?
What is the standard way to make wireless hijacking ble devices hard,...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi, I am using the nRF8001 chip with an external MCU that has both 16MHz and 32KHz crystals. I saw the app note about sharing the 16MHz crystal between MCU and radio. And...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
