The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi,
I'm using the makefile from ble_hrs to write my own makefile. I need to had libraries .lib and .a files.
How should I add my files in the makefile?
Thanks in advance...
hi. dear.
I have custom board using the NRF51822 - nRF24LU1P.
use the gazell protocol.
I want to unencryption key data.
Plz, tell me how to use unencryption key data...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
I have an issue with the ble_app_lbs. I can compile it OK, but when I run it it gets as far as calling sd_ble_gap_device_name_set(), which returns error 0x3001.
Can someone...
Im writing a serial bootloader for the NRF51822 128kB. Im not using much of the SDK and its a custom protocol i.e. no bluetooth. The boot loader can be squeezed into 16kB...
I looked at a very similar thread that had this title for MacOS and I feel that my issues are the same however changing the hardware debugger only changes the error I get...
Halo, is there any linux ( possibly debian or even better raspbian ) driver for
nRF24AP2-USB dongle?
Do you have ANTware II linux ( possibly debian or even better raspbian...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
I'm using Keil to debug my application. Softdevice was loaded w/ Studio and when I click on Debug Keil loads the code but it does not stop at any breakpoint I set. It does...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
First I'm new to these devices and BLE in general.
I am however very experienced at embedded design and Keil tools and ARM processors.
I have got the demo heart beat...
I have the ble_app_hrs communicating with the ble_app_hrs_c, and everything works OK. However, I have to be able to send data in both directions. How do I modify, or what...
I am developing a device converting adc input into data and transmitting them and receiving them at other place,I cant figure out between analog input eg:AIN0 and the port...
Hi,
I'm using nrf51822 with s110 softdevice v6
My question is the following.
How many devices sending advertising messages can be detected at a time by a central unit...
