Hello - We're designing a new app for our product in Flutter. I was writing the proof of concept for the firmware updates, but I hit a roadblock with a Mcu Mgr Error: 25 ...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Working on the nRF52833DK board and based off the nrfx_spim_spis advanced non-blocking example sample. I've already converted the SPI master to use the Zephyr driver instead...
Hi.
After 3 days I've finally got littleFS working on a custom nRF52840 board. I am using nRF connect SDK v2.9.0 which includes Zephyr v3.7.99 with some additional Nordic...
Hello, I hope you are well.
I created a new driver for an i2c accelerometer with 2 gpio interrupts, but it does not build properly. When calling `static const struct device...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hello, sorry if this is a stupid question, but i'm fairly new to BLE (nRF51822), and even newer at report descriptors.
I'm using a nRF51822, SDK6.0.0 and S110 7.0.0.
In...
I saw softdevice no memory every several times, according to spec, softdevice use 8k, and app use 8k, are they share this 16k memory or no sharing, each use 8k, and reduce...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
My PCA10001 was working(running the heart rate monitor example) from the coin cell. After it ceased to work, I assume the cell was flat, but on replacing it the PCA10001 still...
Hello,
i'm trying to get running nRF51 on Arduino IDE. I have forked RFduino at the moment github.com/.../RFduino
With SDK i can compile a startup library and an simple...
I am having a lot of trouble using the new 4.3 Android API. I am trying to develop an application for the Android that will communicate via BLE to a Nordic device. I have...
Hi,
I'm using a 51422 with a s210/s310 softdevice. I have some nodes that must exchange some independent data. So I configured the communication to be an independent bidirectional...
Hi,
I am using SDK6.1 and SD7.0 for our application. I would like to know how to implement the static PIN type pairing?
I have searched Nordic's developers zone and found...
Hello,
I am new to nRF51822, and trying to make a simple application for master - slave data transfer.
I want to know how Much time passes from the start of the device until...
i want to prevent somebody to copy my app by SWD interface,so i set RBPCONF register in main application,but i find that it is no use writing RBPCONF register.
First ,i write...
Hi all,
I am new to nRF51822, and trying to make a simple application for device-to-device data transfer.
I have tried the "ble_app_uart" example, which is for device...
I compiled a new HEX for the pca20006 Beacon based on the ble_app_uart project for the pca10001 (remapped the LEDs and buttons), but when I load the beacon using OTA DFU,...
I compiled a new HEX for the pca20006 Beacon based on the ble_app_uart project for the pca10001 (remapped the LEDs and buttons), but when I load the beacon using OTA DFU,...
Hello all.
I just finished started setting up the environment for Nordic development. We have a Beacon Kit and a nRF51822-EK board.
I managed to compile and run board...
