Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
We created a faster & simpler alternative to gazell for the nRF24LE1 (our IoT sensor) that supports 100s of transmitters (PTXes), is individually addressable, has session...
Hi
I'm using the NRF51422 with hardware UART.
Brief outline of the configuration:
115200 Baud, 8-N-1, no HW flowcontrol
SoftDevice S130 V2.0.1
lib: app uart fifo
...
Hi all,
I am using the softdevice S130 v2.0.1, plus one application derived by the ble_app_uart and the single bank bootloader (SDK11) on a custom board with the nRF51822...
Hello community
I'm trying to do a central app, for this im using the example of UART_Central with the SDK 13 and SD S132.
During the events cycle I am having only the...
Hi,
when executing the following code in my application. if face chip reset time to time. I've investigated code to find the bug origin and then notice that i ve a difference...
i am using Nrf52840 with SDK 132 and version 13.
here is the initialization
ble_radio_notification_init(APP_IRQ_PRIORITY_LOW, NRF_RADIO_NOTIFICATION_DISTANCE_5500US...
I am using ble_app_hids_keyboard example from SDK : nRF5_SDK_12.2.0_f012efa with nRF52 Dev kit. In that example, keys_send() Function is calling under BSP_EVENT_KEY_0. which...
Hi Sir,
I want to run the spi master example code with my nrf52832 board. In sdk11.0, have mentioned for pca 10036, the CS pin should be 29. If that was the condition,...
Sir, I have interfaced nrf board(Master) with msp430(slave) device through spi communication. And Everytime when i am debugging, i got different data(ie,. data which was sent...
Sir,
I wanted to know about transfer of data from nrf to msp430 via spi pins. For this condition, which function/api is used for transmission of single data to slave. What...
I am sorry for asking such silly question,but i failed to search with key word 'gpiote'.
so here is my question,
what is the GPIOTE?
what is the relationship with GPIO...
Hi , I am using the SD 4.0.2, the SDK is 13.0.0_04a0bfd, and the IDE is IAR 8.11.1 to develop production, I integrated the DFU, and I download and updated the APPLICATION...
Hi,
I had been doing nRF52832 porting before
Now, the nRF52840 porting is in progress, but there is no Libraries-trace-app_trace.h file
that was in the old version...
