Hi, the nordic team
I am working on thread protocol using SDK version 2.9.1.
I use the SED device,My poll is 1000 ms. How can I receive messages from my parent node when...
Hello,
I am using the nRF5340 in my project, and the device is capable of communicating with a mobile phone over BLE . However, we occasionally encounter a connection error...
I work for ChannelSounding on nRF54L15.(NCS3.0.1)
I measured the distance using two nRF54L15-DKs. The actual distance was 3m. The average measurement result is shown below...
The nRF52832 devices have been produced in hundreds of units. Currently, it has been found that individual central devices are problematic – connecting to peripherals often...
Dear everyone,
I'm currently working with the nRF7002DK and attempted to build and flash the following project from GitHub: MQTT over WiFi nrf7002DK
However, when building...
Hi,
Is it not possible to import a key which can be used for multiple use cases?
I would like to import a single key which can be used for HMAC & HKDF.
Is the below...
System Info: Hardware: M3 Max OS: Sequoia 15.3 Following the instructions outlined in the readme of: github.com/.../nrf-docker Docker fails to build an image on Apple Silicon...
I have nRF52 and working with SDK11.
I can start BLE advertising and nRF Connect app will detect everything correctly.
I only have an issue: I want to advertise for...
Hi there,
I am getting some error in my SAADC measurements and I believe it's due to the R_INPUT forming a parallel resistance with my voltage divider at the input (the...
Hi,
I am measuring the current during sleep, after the sequence, __WFE();__SEV();__WFE();.
With NRF_LOG_ENABLED set to 1, the current is about 486 uA. With NRF_LOG_ENABLED...
Using: nrf51822, SDK 10.
My application needs to use TWI0 and SPIS1 at the same time. However if I enable TWI0 and then SPIS1, when I run nrf_drv_spis_init() I get NRF_ERROR_INVALID_STATE...
I am working with the SDK 13 ble_app_att_mtu_throughput example. With the SDK 12 example, it seems to require the SoftDevice to be loaded with the arm5_no_packs example. The...
Hello,
I'm designing a project with the nRF52832 where I will use an external SPI ADC.
For debug and backward compatibility purposes, I also plan to use the SAADC.
The...
in the ble multilink central example i'm not understanding where the functions in client_handling.c are exercised some don't seem to be used in main or client_handling (client_handling_dm_event_handler...
I am reporting a problem that might bite you. A Waveshare NRF51822 module comes with a "Passed" sticker on the back (solder side) that makes the module stand off the mother...
Hi,
We are trying to have a thin beacon design. But we are having difficulty in finding low profile inductor for dc-dc converter matching the recommended value of 10uH...
I'd like to use Logic Analyzer in uVision 5.2 and ulink2 for analyzing variables in nrf52832.
In my understanding, I need to use SWO and configure Trace setting properly...
Hi,
I need to capture a demodulated, manchester encoded signal (16 bits long). The data rate is about 50kHz (give or take). Currently, I am configuring a PPI with timer1...
Hello,
I'm using nRF52840 which is surpport Bluetooth 5. I couldn't understand why it can do 8 X range and 2 X data rate than Bluetooth 4.2.
Besides, how to use Bluetooth...
I observe strange behavior while reading value for long characteristics.
I have characteristic 100 bytes long (read only).
In GATT client I must read value with subsequent...
