Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hi,
I am programming with ncs v2.9.0, nrf52833 chips.
I am going to get pc keyboard led state in my custom board throutgh BLE.
This is my report map,but cannot get data...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Hi,
While using the JLinkExe along with the JLinkRTTClient the RTT client eventually stops outputting messages.
After that, both the JLinkExe and the nrfjprog output...
Thank you for the support so far.
I want to ask that if for example in your system or product we want to add bluetooth headphone feature which support Bluetooth 4.0 headphones...
Hi,
I am new to Nordic product and I have NRF52 DK. I have started reading this document
www.nordicsemi.com/.../Getting-started-with-the-nRF52-Development-Kit
However...
Hi,
I am trying to use the BLE v4.2 extended data length on the NRF51822 but the S130 doesn't seem to support it. Please can anyone let me know if it is supported with...
Hi,
I am trying to measure (and reduce) the current consumption of my board. I am using nrf52832 (64K RAM) for my development. The RAM layout is as follows: RAM (rwx) : ORIGIN...
Hello,
Is there any way to mitigate delay of redirecting interrupts from softdevice to application? Using nRF51 with S130 there is ~2us delay even with SoftDevice disabled...
Hello!
I have nRF52 DK and 1 custom designed nrf52832 PCB.
Is it possible to use the one of the nRF52 DK as the BLE dongle and run the ble_app_uart example code on my...
I am developing code to nrf52 and i'm using a sdcard with the adafruit MicroSD card breakout board.
When the sd card has no partitions I'm using the fdisk function (from...
Hi Hi, I am new and I am playing with
nRF5_SDK_12.2.0_f012efa examples in Keil
for some reason I need to use hex file. The files which is generate from those examples...
Hi. I have two codebases here:
A peripheral application on an nRF51822 using SDK 12.2.0, SD 130. It has a vendor-specific service with a characteristic that is write...
Hi,
I am having problem in installing Softwares and drivers required for NRF52.
Please kindly tell me step by step instructions of what software is needed to be install...
I am in the process of getting some nRF52832 based proto units and plan to use the nRF52 DK to load the code and maybe do some external debugging. I will be using P19 (debug...
Hi,
I'm new to embedded development and am trying to interface a 24-bit MEMS microphone (Invensense ICS-43432) using I2S with nRF52 Dev board (PCA10040, V 0.9.0, 2015.39...
Hi,
Basically i want my nRF52 DK should be able to transmit data to connected android device and also be able to receive data from android,data is kind of logs.
