We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Are there any migration guides for a customer who wants to migrate from nRF5340 to nRF54L15? And if they are nRF54L15 in chipscale, anything they should be aware of including...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
Hello - We're designing a new app for our product in Flutter. I was writing the proof of concept for the firmware updates, but I hit a roadblock with a Mcu Mgr Error: 25 ...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
I have been working on making at least 1us Timer interval(expect faster than 1MHz) using interrupt.
To do this we need to set the prescaler of Timer to 4, since formula...
Hello, sorry if this is a stupid question, but i'm fairly new to BLE (nRF51822), and even newer at report descriptors.
I'm using a nRF51822, SDK6.0.0 and S110 7.0.0.
In...
I saw softdevice no memory every several times, according to spec, softdevice use 8k, and app use 8k, are they share this 16k memory or no sharing, each use 8k, and reduce...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
My PCA10001 was working(running the heart rate monitor example) from the coin cell. After it ceased to work, I assume the cell was flat, but on replacing it the PCA10001 still...
Hello,
i'm trying to get running nRF51 on Arduino IDE. I have forked RFduino at the moment github.com/.../RFduino
With SDK i can compile a startup library and an simple...
I am having a lot of trouble using the new 4.3 Android API. I am trying to develop an application for the Android that will communicate via BLE to a Nordic device. I have...
Hi,
I'm using a 51422 with a s210/s310 softdevice. I have some nodes that must exchange some independent data. So I configured the communication to be an independent bidirectional...
Hi,
I am using SDK6.1 and SD7.0 for our application. I would like to know how to implement the static PIN type pairing?
I have searched Nordic's developers zone and found...
Hello,
I am new to nRF51822, and trying to make a simple application for master - slave data transfer.
I want to know how Much time passes from the start of the device until...
i want to prevent somebody to copy my app by SWD interface,so i set RBPCONF register in main application,but i find that it is no use writing RBPCONF register.
First ,i write...
Hi all,
I am new to nRF51822, and trying to make a simple application for device-to-device data transfer.
I have tried the "ble_app_uart" example, which is for device...
I compiled a new HEX for the pca20006 Beacon based on the ble_app_uart project for the pca10001 (remapped the LEDs and buttons), but when I load the beacon using OTA DFU,...
I compiled a new HEX for the pca20006 Beacon based on the ble_app_uart project for the pca10001 (remapped the LEDs and buttons), but when I load the beacon using OTA DFU,...
