Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
Hi,
I connected 74CH595 shift registers to nRF52DK board. When I built and upload my code with Keil everything works just fine, but if I compliled it with GCC and upload...
I want my device not to disconnected.
I'm trying with custom board with NRF51822AA.
I customized NUS example a little.
And also I've downloaded NUS example for Android...
I'm writing a firmware, with SD130, using mbed libraries.
Firmware used to run fine. I added a new object, and now, when connecting, it hardfaults.
I put a breakpoint...
Hi everyone on the community.
I've been struggling trying to upload the hex file created by arduino using redbear nrf arduino fork on a NRF51822 -v2 board that is being...
Hello,
last week I was trying to integrate a wake-on-motion-functionality for my hardware using some interrupt-handling. While that problem is solved, I came across some...
Hello,
I would like to stream sensor data from the Bosch IMU sensor over BLE at a maximum rate. I can collect data over I2C from the sensor but would like to know if there...
Hello to all nordic jedi masters out there!
I am using nRF SDK v11.0 with the nRF52832.
I am a little bit confused about the usage/meaning of the flag argument in the...
Hi all,
I am trying to send a large stream of bytes(60kb) to an NRF52823 using bbowl . BBowl exposes the uart through a TCP socket connection using noble .
I modified...
Hi,
In the schematic presented in the topic 17.1 (dc/dc converter, image below) of the nRF8001 datasheet it isn't shown that AVDD should be connect to a power supply as...
devzone.nordicsemi.com/.../
In this blog this is written:
"Opening and closing a connection event adds a lot of overhead"
how much is the overhead and where can i...
Hello,
I am currently developing a new bt-le-program and besides my own log-messages, I wanted to enable also the log-output that is happing in the files from the Nordic...
I'm building something based on ble_app_gls. However, I only want it to be pairable when I say so (user presses a button to put it into that mode). Is there a "correct" way...
Hi,
upon connection I get these messages via RTT:
nrf_ble_gatt:DEBUG:Peer on connection 0x0 requested an ATT MTU of 185 bytes.
nrf_ble_gatt:DEBUG:Updating ATT MTU to...
I would like to know how to dampen the effect of metal surface on BLE signal . Let me give you an instance, i am installing a wireless sensor inside a metal box and this sensor...
Hi,
I'm trying to make github.com/.../nrf52-spi-i2c-master-ssd1306 to compile with GCC (linux). So far I've managed to get it compiled, but linking fails:
mkdir _build...
